Sensata Magnum Energy ME-RC Скачать руководство пользователя

Страница: 24 / 90

3.0 Setup

Figure 3-6, Current Flow – Inverter Mode

I/C Amps (MS-PAE, MS-PE and MSH inverter models only):

This menu

displays the inverter or charger amps and is shown as an AC value. A negative

(–) amps reading indicates the inverter is powering the inverter loads, and

the batteries are discharging (inverter amps). A positive (+) amps reading

indicates the inverter is using the AC input source to charge the batteries

(charger amps).

AC Input (MSH inverter models only):

This menu displays the RMS value

of the AC voltage at the inverter’s AC1 and NEUTRAL input terminals.

AC2 Input (Dual Source Inverter models only):

This menu displays the

RMS value of the AC voltage at the inverter’s AC2 and NEUTRAL input terminals.

Info:

If the

AC2 Input

menu displays voltage (~ 50v), but the

generator is off or nothing is connected to the AC2 input; this is

normally because the neutral-to-ground bond connection in the

electrical system is not correct or not connected.

• METER: 02 BM: SOC

thru

06 BM: TECH

– These menus allow the

optional ME-BMK (Magnum Energy’s Battery Monitor Kit)—if installed—to be

con

gured to your speci

c system preferences, and displays the status of

the battery system.

Info:

Refer to Section 8.0 (in this manual) and to your ME-BMK/

BMK-NS Owner’s Manual (PN: 64-0013) for detailed information on

these menus and the Battery Monitor Kit.

Example below:



Current to inverter input (Input Amps) = 0 Amps AC



Current from battery (I/C Amps) = -10 Amps AC



Current to power the AC loads (Load Amps) = 10 Amps AC

MAGNUM

INVERTER

Input Amps =

0 Amps AC

Load Amps =

10 Amps AC

I/C Amps =

-10 Amps AC

Inverter

Amp meters

AC CURRENT

(GRID/GEN)

DC CURRENT

(BATTERY)

INVERTER

AC LOADS

-120ADC

FROM

BATT

0AAC

FROM

GRID

10AAC

LOADS

Current from the battery is used by the inverter

to power the inverter’s AC loads.

[

Status/Fault

]

Input Amps: 0AAC

[

Status/Fault

]

I/C Amps: -10AAC

[

Status/Fault

]

Load Amps: 10AAC

INVERTER MODE

Содержание Magnum Energy ME-RC



























































































Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды

Sensata Magnum Energy ME-RC, Руководство пользователя

Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды