Sensata Magnum Energy ME-RC Скачать руководство пользователя

Страница: 35 / 90

3.0 Setup

Table 3-4, Battery Type to Charge Voltages

Battery

Type

Inverter

Voltage

Absorption

Voltage

Float

Voltage

Equalization

Voltage

Fix
ed V

oltage

GEL

12 VDC

14.1 VDC

13.6 VDC

14.1 VDC

24 VDC

28.2 VDC

27.2 VDC

28.2 VDC

48 VDC

56.4 VDC

54.4 VDC

56.4 VDC

Flooded

12 VDC

14.6 VDC

13.4 VDC

15.5 VDC

24 VDC

29.2 VDC

26.8 VDC

31.0 VDC

48 VDC

58.4 VDC

53.6 VDC

62.0 VDC

AGM1

12 VDC

14.3 VDC

13.3 VDC

15.5 VDC

24 VDC

28.6 VDC

26.6 VDC

31.0 VDC

48 VDC

57.2 VDC

53.2 VDC

62.0 VDC

AGM2

12 VDC

14.5 VDC

13.5 VDC

14.5 VDC

24 VDC

29.0 VDC

27.0 VDC

29.0 VDC

48 VDC

58.0 VDC

54.0 VDC

58.0 VDC

LFP

12 VDC

14.4 VDC

13.6 VDC

14.4 VDC

24 VDC

28.8 VDC

27.2 VDC

28.8 VDC

48 VDC

57.6 VDC

54.4 VDC

57.6 VDC

Adjustable V

oltage

Custom

12 VDC

12.0-16.0 VDC 12.0-16.0 VDC 12.0-16.0 VDC

24 VDC

24.0-32.0 VDC 24.0-32.0 VDC 24.0-32.0 VDC

48 VDC

48.0-64.0 VDC 48.0-64.0 VDC 48.0-64.0 VDC

CC/CV

12 VDC

12.0-16.0 VDC 12.0-16.0 VDC 12.0-16.0 VDC

24 VDC

24.0-32.0 VDC 24.0-32.0 VDC 24.0-32.0 VDC

48 VDC

48.0-64.0 VDC 48.0-64.0 VDC 48.0-64.0 VDC

Note¹:

Voltage same as absorption voltage—to prevent equalization charge.

Note²:

Charge voltages for Concord (Lifeline Series) AGM batteries.

Note³:

Charge voltages for East Penn, Deka, Discover and Trojan AGM batteries.

Note

When using Custom setting, the EQ (Equalization) voltage adjustment

cannot be set lower than the Absorb Voltage setting. Also, the EQ Voltage

adjustment cannot be set higher than 2 volts (12-volt systems), 4 volts (24-

volt systems), or 8 volts (48-volt systems) above the Absorb Voltage setting.

Note

For inverter models <Level 5, the Float Voltage level is

13.1 VDC

(12-volt models); 26.2 VDC (24-volt models); or 52.4 VDC (48-volt models).

See Section 3.2 for inverter level information.

CAUTION:

If using Lithium batteries and selecting the LFP battery

type pro

le—to prevent the charger’s output voltage level from

changing based on temperature—REMOVE the BTS from the inverter.

Info:

The charge voltage levels shown in Table 3-4 are with the

Battery Temperature Sensor (BTS) at a temperature of 77° F (25° C),

or not connected. If the BTS is connected, the actual charge voltage

level will increase if the temperature around the BTS is below 77° F

(25° C), and decrease if higher than 77° F (25° C). This ensures the

batteries receive the correct charge voltage regardless of temperature.

Содержание Magnum Energy ME-RC



























































































Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды

Sensata Magnum Energy ME-RC, Руководство пользователя

Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды