Sensata Magnum Energy ME-RC Скачать руководство пользователя страница 26

Страница: 26 / 90

3.0 Setup

Press to save

SETUP

Press

Status...

01 Search Watts

Rotate to

Press to select

Rotate to

desired

selection:

Range: OFF, 5-50 Watts (increments by 5 Watts)

Figure 3-9, SETUP: 01 Search Watts Selections

• SETUP: 01 Search Watts

– Allows you to turn off the Search Watts

feature, or to adjust the power level to determine when the inverter leaves

Search mode. If not needed, select

OFF

. When search is turned off, the

inverter continuously provides full AC voltage to the loads.

Default setting:

Search = 5W

Range:

OFF, 5-50 Watts (5 Watt increments)

Info:

When the Search Watts feature is active, “

Searching

” appears

on the top line of the LCD display and the green INV LED will

ash.

What is the Search Watts feature? This feature helps save battery power by

reducing the inverter’s output to search pulses when there is no detectable

load. If a load greater than the wattage level setting turns on while the

inverter is searching, the inverter starts inverting to provide full voltage on

its output.
Should I use the Search Watts feature? If the inverter can spend a great

deal of time searching (to reduce the power drain on your batteries) and you

can tolerate small loads (<5 watts) being off, then the Search mode feature

should be used. However, if some small loads (i.e., digital clocks, satellite

receivers, answering machines, etc.,) are required to be on, then this feature

should be turned off (

Search = OFF

Where should I set Search Watts? This setting should be adjusted to the same

power level (or the next lower setting) of the smallest load that you plan to

run. If you don’t know the wattage of the smallest load, turn the load on and

decrease the

Search Watts

setting until the load comes on and stays on.

Info:

Even though the Search feature is on, some connected

equipment—even if they are off—may draw enough current to keep

the inverter in the Inverting mode (i.e., not “Searching”).

3.3.4 SETUP

Menu

Pressing the SETUP menu button provides access to menu items and settings

that allow the inverter/charger to be con

gured. Review each menu item to

determine if any setting requires adjustment to meet your requirements.

Содержание Magnum Energy ME-RC



























































































Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды

Sensata Magnum Energy ME-RC, Руководство пользователя

Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды