Sensata Magnum Energy ME-RC Скачать руководство пользователя

Страница: 68 / 90

7.0 Using an AGS

AGS: 03 Run Time Hour Menu

This menu provides the settings that determine the length of time the

generator will run once it has been autostarted by the AGS.

Default setting:

Run Time = 2.0 Hrs

Range:

0.5 - 25.5 Hrs (0.5 hr increments)

How long should I set the generator run time?

This depends on whether

you are using the high temperature or low battery voltage autostart feature.

• Using high temperature to autostart:

When using the high

temperature autostart feature, the generator autostarts and runs until the

AGS: 04 Start Temp F

setting is reached. This means you could set the time

to the lowest time setting (

0.5 Hrs

), knowing the generator will run until the

temperature setting is satis

ed.

• Using low battery voltage to autostart:

When using the low battery

voltage autostart feature, the generator run time is normally set to help re-

charge the batteries. Use Table 7-2 below to help determine the generator

run time setting based on the 20-hour AH capacity of your inverter’s battery

bank.

Table 7-2, Battery AmpHrs Capacity to Suggested Gen Run Time

AGS: 04 Start Temp F Menu

This menu allows you to set and enable a temperature value that will cause

the generator to automatically start—to power an air conditioner (A/C)

unit for cooling—based on an increase in temperature, or by using an air

conditioning thermostat control.

Info:

Optional ME-PT1 or ME-PT2 pigtail adapters can be used to

connect an AC control circuit or a relay control circuit. For more

info, refer to the instruction sheet for each pigtail adapter—part #

64-0025 (ME-PT1 instructions), or #64-0026 (ME-PT2 instructions).

This temperature autostart feature requires that the AGS’s remote

temperature sensor cable or an optional ME-PT1 or ME-PT2 pigtail adapter

be connected to the REMOTE port on the AGS. The location of the remote

temperature sensor determines the area being monitored for temperature.

When the temperature around the remote temperature sensor (based on

the

AGS: 08 AGS TECH

menu’s

Temp

display) increases to the

AGS: 04

Start Temp F

setting, the generator automatically starts and runs based on

the

AGS: 03 Run Time Hour

setting. When this run time period is

nished,

the temperature sensor reading is checked. If the temperature sensor (or

thermostat control—if using the optional pigtail adapter) reading is below the

AGS: 04 Start Temp F

setting, the generator will autostop. If the temperature

Battery

AmpHrs

Capacity

Suggested

Gen Run Time

Battery

AmpHrs

Capacity

Suggested

Gen Run Time

200 to 300

1 hour

1310 to 1500

4 hours

310 to 500

1.5 hours

1510 to 1700

4.5 hours

510 to 700

2 hours

1710 to 1900

5 hours

710 to 900

2.5 hours

1910 to 2100

5.5 hours

910 to 1100

3 hours

2110 to 2300

6 hours

1110 to 1300

3.5 hours

2310 to 2500

6.5 hours

Содержание Magnum Energy ME-RC



























































































Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды

Sensata Magnum Energy ME-RC, Руководство пользователя

Результаты поиска

Содержание Magnum Energy ME-RC

Отзывы:

Похожие инструкции для Magnum Energy ME-RC

Бренды по названию

Популярные бренды