manualshive.com logo in svg

Sea Recovery SRC Aqua Matic 1400-2, Руководство пользователя, Страница: 83 / 223

Поделиться
Скачать
Sea Recovery SRC Aqua Matic 1400-2 Скачать руководство пользователя страница 83

81

NOTE:

 If the control system is unable to successfully calibrate the pressure control regulator, an

error message will be displayed, and automatic startup  will be aborted. An example of
this error message is shown below:

NOTE:

 There will be a system priming delay of approximately 25 second once boost pump has

turned on to when the HP Pump turns on.

4. For Aqua Whisper DX system increase pressure to 950 PSI  (65 BAR)  by

turning the regulator valve.

NOTE:

  For Aquamatic & Aquamatic  XL systems, after a further 60 seconds the system will

activate the automatic pressure regulator and start increasing system pressure until the
desired product water production rate has been achieved or until max pressure allowable
(925 PSI - 65 BAR). If  Max pressure is achieved, you will get a warning message. This
will most likely happen when you are in low temperature, high salinity feed water, or when
your membranes need cleaning or changing. The Aquamatic and Aquamatic XL system
will continue to operate in this high-pressure state and will divert all potable water
produced into the ships potable water storage tank.

Содержание SRC Aqua Matic 1400-2
































































































































































































































Отзывы:

Нет отзывов