manualshive.com logo in svg

Sea Recovery SRC Aqua Matic 1400-2, Руководство пользователя, Страница: 76 / 223

Поделиться
Скачать
Sea Recovery SRC Aqua Matic 1400-2 Скачать руководство пользователя страница 76

Manual Operation

 

The Aquamatic, Aquamatic XL and AquaWhisper  DX desalination system controller provides

 

two possible methods of operation; these are manual mode and automatic mode. In manual

 

mode,  the controller requires that the operator activate the relative pumps by pressing on the

 

required pump operation icons. If the user attempts to operate a pump when it is determined by

 

the control system as unsafe to do so, the controller will not allow such an action and will in

 

some cases raise a warning message.

NOTE:

 Before attempting manual start up, it is important to check that all system feed and brine

valves are in the open position.

1. Press anywhere on the main splash screen to begin.

2. Press Operations icon shown below.

3. Press Manual Mode icon shown below.

NOTE:

  The  Manual control screen displayed may vary from the examples shown below,

depending on the product model in use. To provide complete details, this manual will
review the procedures needed for operation of an Aquamatic, or Aquamatic XL system.
Hence, this description will contain automatic pressure regulation operation information
that is not needed when operating an AquaWhisper DX system.

Press
Here

Press Here

Aqua Matic Compact 450-1800

7

4

Содержание SRC Aqua Matic 1400-2
































































































































































































































Отзывы:

Нет отзывов