Sea Recovery SRC Aqua Matic 1400-2 Скачать руководство пользователя страница 82

Страница: 82 / 223

Automatic Operation

Automatic startup operation allows for virtually hands free startup of the Aquamatic, Aquamatic

XL or AquaWhisper DX system, and all associated equipment. This automatic startup operation

can also be carried out remotely via the system remote control display (if installed).

NOTE:

Before attempting automatic start up, it is important to check that all system feed and

reject valves are in the correct position.

1. Press anywhere on the main splash screen to begin.

2. Press Operations icon shown below.

3. Press the Start or Auto Start/Stop icon.

Auto Start/Stop
shortcut (available
on any screen)

Press
Here

Press Here

Aqua Matic Compact 450-1800

Содержание SRC Aqua Matic 1400-2
































































































































































































































Результаты поиска

Содержание SRC Aqua Matic 1400-2

Отзывы:

Sea Recovery SRC Aqua Matic 1400-2, Руководство пользователя, Страница: 82 / 223

Результаты поиска

Содержание SRC Aqua Matic 1400-2

Отзывы: