manualshive.com logo in svg

Sea Recovery SRC Aqua Matic 1400-2, Руководство пользователя, Страница: 130 / 223

Поделиться
Скачать
Sea Recovery SRC Aqua Matic 1400-2 Скачать руководство пользователя страница 130

22

Operation requested in feed water
warmer than system temperature
specifications.

The user requested system operation, but the feed
water is hotter than permitted for accurate system
operation. The system salinity sensor is calibrated to

read salinity accurately in water up to 40C. Water
above this temperature will yield unknown results and
as such, the control system will not allow operation in
these waters.

23

Operation requested in feed water
colder than system temperature
specifications.

The user requested system operation, but the feed
water is colder than permitted for accurate system

operation. The system salinity sensor is calibrated to
read salinity accurately in water down to 5C. Water
below this temperature will yield unknown results and
could freeze once purified by the system RO
membranes and as such, the control system will not
allow operation in these waters.

24

Maximum emergency operation
time expired. Please contact
Parker for assistance.

The system has been operating with a critical sensor in
bypass mode for the maximum allowable time. The unit
will no longer operate until this fault is repaired. In
emergencies, it is possible to reset the by-pass
operation timer. Please contact Parker further help

25

Operator did not increase system

pressure within allowed time.

The system was started in either manual mode or the
system is an AquaWhisper DX. Once the HP pump is
activated, the user has a finite time in which to adjust

system pressure to above minimum (>250PSI), if this
step is not taken, the system automatically shuts down
and generates this message.

26

BPR drive current exceeded. BPR
is jammed

During operation of the system BPR, the current
required to turn the unit exceeded the allowable
maximum. This indicates to the controller that the BPR
is jammed, or the motor has failed and has an internal
short circuit. If the BPR is not jammed and moves freely,
Contact Parker for further assistance

27

BPR jam occurred while opening
valve. Auto release will be
attempted once alarm is

accepted.

While operating the BPR valve in a clockwise direction,
the valve current rose exponentially, indicating the
valve has reached a fully closed position, when this
message is accepted by the user, the control system will

use all available motor power to release the valve from
this jammed position.

28

BPR jam occurred while closing
valve. Auto release will be
attempted once alarm is
accepted.

While operating the BPR valve in a counterclockwise
direction, the valve current rose exponentially,
indicating the valve has reached a fully open position,
when this message is accepted by the user, the control
system will use all available motor power to release the
valve from this jammed position.

Aqua Matic Compact 450-1800

12

8

Содержание SRC Aqua Matic 1400-2
































































































































































































































Отзывы:

Нет отзывов