Section 07 BODY AND HULL
Subsection 02 (BODY)
For dirt build-up, use
BRP PLASTIC & VINYL
CLEANER (P/N 413 711 200)
, Vinyl Finish Vinyl
Cleaner or an equivalent. Let soak for approxi-
mately 10 minutes, then gently scrub with a soft
bristle brush. For specific stain removal, refer to
your cleaning and care card.
Do not use any silicone-based protectants. They
will extract the plasticizers, leaving the vinyl hard
and brittle, and eventually cracking will occur.
RECOMMENDED PRODUCTS
1.
BRP Plastic and Vinyl Cleaner
(P/N 413 711 200)
2. Dish Soap (Dawn or Ivory)
3. Fantastik
4. 3M Citrus Cleaner
5. 303 Protectant
Vinyl Cleaning Recommendations for Special
Stains
TYPE OF
STAIN
STEP
1
STEP
2
STEP
3
ACTION
Ballpoint ink*
E
B
A
Chewing gum
D
A
—
Coffee, tea,
chocolate
B
—
—
A. Medium-soft brush,
warm soapy water,
rinse/dry.
Pen
D
B
—
Grease
D
B
—
Household soil
A
B
—
B. Vinyl Finish Cleaner,
rinse/dry.
Ketchup
A
B
—
Latex paint
A
B
—
Lipstick
A
B
—
Mildew or wet
leaves*
C
B
A
Motor oil
B
—
—
C. One (1) tablespoon
of ammonia, one-fourth
(1/4) cup of hydrogen
peroxide, three-fourth
(3/4) cup of water,
rinse/dry.
Oil-based paint
D
B
—
Permanent
marker*
E
B
C
Spray paint
B
B
—
D. Wipe or scrape off
excess (chill gum with
ice before hand).
Suntan lotion
A
B
—
Tar/asphalt
D
B
—
Yellow mustard
A
B
C
E. Denatured alcohol,
rinse/dry.
* Suntan lotion, tree pollen, wet leaves and some other
products can contain dyes that stain permanently.
All cleaning methods must be followed by a thor-
ough rinse with warm water.
Certain household cleaners, powdered abrasives,
steel wool and industrial cleaners can cause dam-
age and discoloration and are not recommended.
Dry cleaning fluids and lacquer solvents should
not be used as they will remove printed pattern
and gloss. Waxes should be used with caution
as many contain dyes or solvents that can perma-
nently damage the protective coating.
SEAT LATCH
Seat Latch Adjustment
NOTE:
Apply
LOCTITE 243 (BLUE) (P/N 293 800 060)
on threads of lock pin when the adjustment is re-
quired or when the lock pin is removed. If a new
lock pin is used, it is already coat with a thread-
locker.
1. Loosen adjustment nut.
2. Adjust lock pin height. Do not torque yet.
3. Close and latch seat.
4. Pull lock pin rearward and tighten adjustment
nut.
smr2009-042-033_a
1. Lock pin
2. Adjustment nut. Torque to 8 N•m (71 lbf•
in
)
A. 32.0 mm ± 0.5 mm (1.26 in ± .02 in)
BUMPERS
Bumper Removal
Front Bumper
1. Remove both protective caps.
482
smr2009-042
Содержание GTX Limited iS 255 2009
