Section 03 ELECTRONIC MANAGEMENT SYSTEMS
Subsection 04 (MONITORING SYSTEM AND FAULT CODES)
FAULT
CODE
MODULE
DESCRIPTION
POSSIBLE CAUSE
SERVICE ACTION
C2151
iBR
System disabled and
need activation
System is locked.
Need activation
Use B.U.D.S. iBR unlock function.
Refer to the Service Manual for more
details.
C2155
iBR
Water temperature
sensor overheat
iBR cooling system
failure.
iBR unit failure
Check iBR cooling circuit.
Replace iBR unit.
Refer to the Service Manual for
more details.
C2161
iBR
Low voltage detected
Battery failure, rectifier
failure, damaged circuit
wires, battery terminal
connection, damaged AC
generator or damaged
connectors
Check fuses 15 (refer to
WIRING
DIAGRAM
).
Check ground continuity to the
engine block.
Refer to the Service Manual for
more details.
C2200
iS
Sensors calibration is
corrupted
Incompatible firmware or
memory failure (Internal
memory failure, return to
supplier)
Defective iS module, replace module
and return to supplier.
C2210
iS
Bridge/CPU
temperature sensor
overheat
Hardware failure or
external heat source
Check for over utilization/heat.
C2220
iS
Application calibration
is corrupted
Incompatible firmware or
memory failure (B.U.D.S.
should repair that)
Program calibration with B.U.D.S.
C2221
iS
Application
parameters corrupted
(backup no. 1
or no. 2)
Battery power lost or
memory failure (Reset
after power-down-up,
clear fault.
If happens often, verify
supply voltage)
Check power wiring and fuse.
C2222
iS
Last session
interrupted
Unexpected battery
power lost
Check power wiring and fuse.
C2230
iS
Internal motor drive
failure
Motor voltage feedback
not fitting with the
command
Defective iS module, replace module
and return to supplier.
C2231
iS
Motor shorted to
ground/battery
Current leak detected
when the bridge is off
Check suspension actuator pump
wiring.
C2232
iS
Motor open
No current while
activated
Check suspension actuator pump
and/or wiring.
C2233
iS
Motor current
software breaker
Motor current too high
Check suspension actuator pump.
C2240
iS
Seat position sensor
error Open, Shorted
to Gnd
Sensor not connected
Check system circuit at iS module
(refer to
WIRING DIAGRAM
).
C2250
iS
System current
software breaker
Battery input current too
high
Check suspension actuator pump.
C2251
iS
System disabled and
need activation
System is locked
for safety.
Need activation
Activate iS using B.U.D.S. activation
function.
196
smr2009-029
Содержание GTX Limited iS 255 2009
