Sea-doo GTX DI 5649 Скачать руководство пользователя | Manualshive

Страница: 7 / 91

background image

5

FOREWORD

The

Operator’s Guide

and

Safety Hand-

book

have been prepared to acquaint

the owner/operator or passenger with
this personal watercraft and its various
controls, maintenance and safe riding
instructions. Each is indispensable for
the proper use of the product, and
should be kept in a waterproof bag with
the watercraft at all times.

For any questions pertaining to the
warranty and its application, consult
the WARRANTY section in this Guide,
and/or an authorized SEA-DOO dealer.

This guide uses the following symbols
to emphasize particular information.

CAUTION:

Denotes an instruction

which, if not followed, might damage
the watercraft and/or components.

NOTE:

Indicates supplementary infor-

mation needed to fully complete an in-
struction.

Although the mere reading of such in-
formation does not eliminate the haz-
ard, the understanding and application
of the information will promote its cor-
rect use.

The information and components/
system descriptions contained in this
guide are correct at the time of publica-
tion. Bombardier Inc. however, main-
tains a policy of continuous improve-
ment of its products without imposing
upon itself any obligation to install
them on products previously manufac-
tured.

Because of our ongoing commitment
to product quality and innovation, Bom-
bardier Inc. reserves the right at any
time to discontinue or change specifica-
tions, designs, features, models or
equipment without incurring obligation.

The illustrations in this document show
the typical construction of the different
assemblies and may not represent the
full detail or exact shape of the parts.
However, they represent parts that
have the same or similar function.

It is understood that this guide may be
translated into another language. In
the event of any discrepancy, the En-
glish version shall prevail.

Specifications are given in the SI met-
ric system with the SAE U.S. equiva-
lent in parenthesis. Where precise ac-
curacy is not required, some conver-
sions are rounded off for easier use.

A

Shop Manual

can be obtained for

complete service, maintenance and
more repair information.



WARNING

Identifies an instruction which, if
not followed, may cause serious
personal injuries including the
possibility of death.

smo2000-003a.book Page 5 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

«
...
5
6
7
8
9
...
»

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Похожие инструкции для GTX DI 5649

Бренд: Native Watercraft Страницы: 6

2870 Walkaround

Бренд: PURSUIT Страницы: 140

Бренд: Blue Wave Boats Страницы: 1

Бренд: Hobie Страницы: 20

Бренд: Access Страницы: 27

Бренд: Four winns Страницы: 79

Бренд: Grady-White Boats Страницы: 66

Бренд: Grady-White Boats Страницы: 76

Бренд: Grady-White Boats Страницы: 78

Бренд: Grady-White Boats Страницы: 74

Бренд: Grady-White Boats Страницы: 76

Бренд: Grady-White Boats Страницы: 87

Бренд: Hunter Страницы: 157

Бренд: Marine Power Страницы: 79

Бренд: J/Boats Страницы: 23

SWIFT TRAWLER 42

Бренд: BENETEAU Страницы: 132

Бренд: Nautiraid Страницы: 12

Бренд: Ranger Tugs Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды