Sea-doo GTX DI 5649 Скачать руководство пользователя

Страница: 51 / 91

Flushing

To flush cooling system, start the en-
gine

then

immediately open the water

tap.

CAUTION:

Never flush a hot engine.

Always start the engine before
opening the water tap. Open water
tap immediately after engine is
started to prevent overheating.

Ensure water flows out of drain lines
(engine crankcase, engine cylinder and
air compressor (

DI models

) while

flushing. Otherwise, clean the lines.

Run the engine about 3 minutes at a
fast idle around 3500 RPM.

CAUTION:

Never run engine longer

than 5 minutes. Drive line seal has no
cooling when watercraft is out of wa-
ter.

Lubrication

Carburetor-Equipped Models

Spray BOMBARDIER LUBE lubricant
or equivalent, through hole of air intake
silencer keeping engine at fast idle
during one minute.

1. Air intake silencer
2. Spray BOMBARDIER LUBE here

DI Models

Spray BOMBARDIER LUBE lubricant
or equivalent, through hole of air intake
silencer during one minute.

NOTE:

An increase of engine RPM

may be noticed while spraying the lu-
bricant in the air intake silencer.

1. Partially pull tube out of air box to inject

BOMBARDIER LUBE lubricant or equivalent.
Push tube in when finished

Carburetor-Equipped Models

After approximately half a minute,
close fuel tank valve (if so equipped) to
run engine out of fuel while lubricating.

CAUTION:

When engine begins to

run irregularly because of fuel star-
vation, immediately stop water flow
before engine dies.

Close the water tap then stop the en-
gine.

CAUTION:

Always close the water

tap before stopping the engine.

All Models

Final Steps

Disconnect the garden hose.

Remove spark plug cables and con-
nect them on the grounding device.



WARNING

Components inside engine com-
partment may be hot. Do not touch
any electrical parts or jet pump
area when engine is running.

F02H0ZY



WARNING

A lw ay s u se s pa rk p lug cab le
grounding device when removing
spark plugs.

F12F01Y

smo2000-003a.book Page 49 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Содержание GTX DI 5649




























































































Результаты поиска

Содержание GTX DI 5649

Отзывы:

Похожие инструкции для GTX DI 5649

Бренды по названию

Популярные бренды

Sea-doo GTX DI 5649, Руководство оператора

Результаты поиска

Содержание GTX DI 5649

Отзывы:

Похожие инструкции для GTX DI 5649

Бренды по названию

Популярные бренды