Sea-doo GTX DI 5649 Скачать руководство пользователя | Manualshive

Страница: 49 / 91

background image

47

Stopping/Docking

The watercraft is slowed by water drag.
The stopping distance will vary depend-
ing on the craft size, weight, speed, wa-
ter surface condition, presence and di-
rection of wind and current.

The operator should become familiar-
ized with the stopping distance under
different conditions.

Release the throttle at a sufficient dis-
tance before the expected landing area.

Reduce speed to idle.

Shift to neutral, reverse or forward, as
required.

Beaching

CAUTION:

It is not recommended to

run the watercraft to the beach.

Come slowly to the beach and shut off
the using the safety lanyard when wa-
ter depth is 90 cm (3 ft) under the hull,
then pull the watercraft to the beach.

Shutting Off the Engine

To keep watercraft directional control,
the engine should be running until the
watercraft is at idle.

To shut off the engine, completely re-
lease throttle lever and press the en-
gine start/stop button. Remove safety
lanyard from watercraft.



WARNING

Directional control is reduced when
throttle is released and lost when
engine is off.

F01L50Y



WARNING

Should the engine be shut off,

wa-

tercraft

directional control is lost.

Never leave the safety lanyard on
an unattended watercraft in order
to avoid unauthorized use or theft.

F07A0EY

smo2000-003a.book Page 47 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

«
...
47
48
49
50
51
...
»

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Похожие инструкции для GTX DI 5649

Бренд: Mareplast Страницы: 5

Бренд: SeaDoo Страницы: 39

Бренд: Sea-doo Страницы: 15

Бренд: Sea Ray Boats Страницы: 26

Бренд: Sea Eagle Boats Страницы: 8

Бренд: Sea Eagle Страницы: 13

Бренд: Sea Ray Страницы: 80

Бренд: Sea-doo Страницы: 202

Бренд: Sea-doo Страницы: 314

Бренд: Hobie Страницы: 28

Бренд: Sea-doo Страницы: 123

Бренд: Crivit Страницы: 38

Бренд: Hunter Страницы: 196

Бренд: Hunter Страницы: 210

Бренд: Hunter Страницы: 210

Бренд: Zodiac Страницы: 38

GP800R WaveRunner 2005

Бренд: Yamaha Страницы: 122

Бренд: udir/c Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды