Sea-doo GTX DI 5649 Скачать руководство пользователя | Manualshive

Страница: 43 / 91

background image

41

TYPICAL

1. Reverse gate in middle position

To obtain reverse, pull shift lever com-
pletely. The reverse gate will be in
downward position, directing all the
thrust toward the front of the water-
craft.

1. Shift lever in reverse position

TYPICAL

1. Reverse gate in downward position

NOTE:

To obtain maximum efficiency

and control from the reverse, increase
engine speed to slightly above idle.
Too much RPM will create water tur-
bulence and reduce reverse efficiency.

GTX DI Models

In reverse position, turn the handlebar
in the opposite direction that you want
to move the rear of the watercraft.

For example, to steer the rear of the
watercraft to the left side, turn the
handlebar to the right side.

1. Handlebar turned to the right side
2. Rear of

watercraft

moving to the left side

RX Models

In reverse position, turn the handlebar
in the same direction that you want to
move the rear of the watercraft.

For example, to steer the rear of the wa-
tercraft to the left side, turn the handle-
bar to the left side.

All Models

F07J0NY

1

F07L0SY

1

F07J0OY

1



WARNING

Shift lever should only be used
when the engine is idling. Do not
use reverse to stop the watercraft.

F07A0CY

1

2

smo2000-003a.book Page 41 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

«
...
41
42
43
44
45
...
»

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Похожие инструкции для GTX DI 5649

Бренд: Jeanneau Страницы: 15

Бренд: J/Boats Страницы: 88

Fairline Phantom Flybridge Cruisers 46 -...

Бренд: FAIRLINE Страницы: 24

Бренд: Outcast Страницы: 6

Бренд: ABSTRACT Страницы: 12

Бренд: NorthStar Страницы: 2

Бренд: NorthStar Страницы: 2

Бренд: Boston Whaler Страницы: 80

Бренд: Hobie Страницы: 2

Бренд: Westport Страницы: 11

Бренд: J&J Amusements Страницы: 171

Бренд: SEABOB Страницы: 82

Performance 405

Бренд: Baja Страницы: 88

Бренд: Pelican Страницы: 2

Бренд: BENETEAU Страницы: 138

Бренд: Jeanneau Страницы: 115

Бренд: Grand Страницы: 19

MK II FORMOZA 550 SOF COMBAT

Бренд: Wayland Folding Kayaks Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды