Sea-doo GTX DI 5649 Скачать руководство пользователя | Manualshive

Страница: 70 / 91

background image

68

Pour approximately 200 mL (7 oz) of
antifreeze in hose. This will protect the
valve and the muffler.

Remove temporary hose and recon-
nect hose to valve.

All Models

Most of the antifreeze will drain out
when removing the hose pinchers. Use
a container to recover it. DISPOSE AN-
TIFREEZE AS PER YOUR LOCAL LAWS
AND REGULATIONS.

NOTE:

Although antifreeze will mainly

drain out, the antifreeze has mixed with
the water that was possibly trapped in
the water jackets and thus preventing
freezing problems.

At pre-season preparation, drain the
remaining antifreeze from cooling sys-
tem prior to using the watercraft.

The following steps should be per-
formed to provide the watercraft en-
hanced protection.

Clean the bilge with hot water and de-
tergent or with bilge cleaner. Rinse
thoroughly. Lift front end of watercraft
to completely drain bilge. If any repairs
are needed to body or to the hull con-
tact your authorized Sea-Doo dealer.
For paint touch up to mechanical parts
use Bombardier spray paint.

Reinstall vent tube support (

if applica-

ble

).

Anticorrosion Treatment

Wipe off any residual water in the en-
gine compartment.

Spray BOMBARDIER LUBE lubricant
or equivalent over metallic compo-
nents in engine compartment.

Lubricate the throttle cable with BOM-
BARDIER LUBE lubricant or equivalent.

Final Steps

Apply a good quality marine wax to the
body.

The seat and the seat extension (

if so

equipped

) should be partially left

opened, and storage baskets (

if so

equipped

) should be removed during

storage. This will avoid engine com-
partment condensation and possible
corrosion.

If the watercraft is to be stored out-
side, cover it with an opaque tarpaulin
to prevent sun rays and grime from af-
fecting the plastic components, water-
craft finish as well as preventing dust
accumulation.

CAUTION:

The

watercraft

should

never be left in water for storage.
Never leave the

watercraft

stored in

direct sunlight.

Pre-Season Preparation

Use the following chart.

Since technical skills and special tools
are required, some operations should
be performed by an authorized Sea-
Doo dealer.



WARNING

Do not lubricate the safety lanyard
post.



WARNING

Observe all WARNINGS and CAU-
TIONS mentioned throughout this
guide which are pertinent to the
item being checked. When compo-
nent conditions seem less than
satisfactory, replace with genuine
BOMBARDIER parts or approved
equivalents.

smo2000-003B.fm Page 68 Wednesday, November 17, 1999 8:18 AM

www.SeaDooManuals.net

«
...
68
69
70
71
72
...
»

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Похожие инструкции для GTX DI 5649

Бренд: Nacra Страницы: 28

1989 2150 Cuddy Outboard

Бренд: PURSUIT Страницы: 36

Бренд: RS SAILING Страницы: 70

45 COCKPIT MOTOR

Бренд: Carver Страницы: 141

Sea-Doo FT Series

Бренд: BRP Страницы: 212

Бренд: Prestige Страницы: 120

Бренд: Regal Страницы: 315

Бренд: Regal Страницы: 326

Бренд: Sea-doo Страницы: 7

Бренд: Sea-doo Страницы: 71

Бренд: Canadian Electric Boat Company Страницы: 32

Бренд: Nacra Страницы: 24

Бренд: Candela Страницы: 55

Бренд: PATHFINDER Страницы: 32

Бренд: Hobie Страницы: 8

Бренд: Wellcraft Страницы: 111

180 SPORTSMAN O/B

Бренд: Wellcraft Страницы: 180

Бренд: Sea Ray Boats Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды