Sea-doo GTX DI 5649 Скачать руководство пользователя | Manualshive

Страница: 14 / 91

background image

12

5. LIMITATIONS OF LIABILITY

This warranty gives you specific rights, and you may also have other legal rights which may
vary from state to state, or province to province.

WHERE APPLICABLE, THIS WARRAN-

TY IS EXPRESSLY GIVEN AND ACCEPTED IN LIEU OF ANY AND ALL OTHER WAR-
RANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WAR-
RANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Neither the distributor, any authorized SEA-DOO dealer nor any other person has been
authorized to make any affirmation, representation or warranty other than those contained
in this warranty, and if made, such affirmation, representation or warranty shall not be
enforceable against BOMBARDIER or any other person.
In no event shall BOMBARDIER be liable for special, consequential or incidental damages,
including but not limited to loss of use and transportation costs. Some states or provinces
do not allow the exclusion or limitation of incidental or consequential damages, or limitations
on how long an implied warranty lasts, so the above limitation or exclusion may not apply.
BOMBARDIER reserves the right to modify this warranty at any time, being understood
that such modification will not alter the warranty conditions applicable to the SEA-DOO
sold while this warranty is in effect.

6. TRANSFER

If the customer sells the SEA-DOO watercraft guaranteed under the present, he shall
assign and transfer this warranty, which shall be valid for the rest of the relevant PERIOD
as defined in section 1 hereinabove, to the new customer.

7. CONSUMER ASSISTANCE

a) In the event of a controversy or a dispute arising in connection with this BOMBARDIER

LIMITED WARRANTY, BOMBARDIER suggests that you try to resolve the issue at the
dealership level. We recommend discussing the issue with the authorized dealer's ser-
vice manager or owner.

b) If further assistance is required, Bombardier`s service department should be contacted

in order to resolve the matter in Canada and the USA.

c) If the issue has still not been resolved, please submit in writing your complaint to:

BOMBARDIER INC.
RECREATIONAL PRODUCTS

CUSTOMER ASSISTANCE CENTER
75, J.-A. BOMBARDIER STREET
SHERBROOKE, QC
J1L 1W3
Tel.: (450) 532-5000

SEPTEMBER 1999
® Trademark of Bombardier Inc. and/or its subsidiaries.

In Canada and USA:

smo2000-003a.book Page 12 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

«
...
12
13
14
15
16
...
»

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Похожие инструкции для GTX DI 5649

Бренд: NEILPRYDE Страницы: 4

Invitation Triss Racer

Бренд: BOMBARDIER Страницы: 23

3125 GFX OFFSHORE

Бренд: Kingfisher Страницы: 50

60 Day Cruiser 2020

Бренд: YAMARIN Страницы: 100

Бренд: Ranger boats Страницы: 80

Бренд: GALA Страницы: 10

Бренд: GALA Страницы: 10

Бренд: C&C Страницы: 34

Бренд: LaserPerformance Страницы: 16

Бренд: LaserPerformance Страницы: 21

2010 Ranger Tug R-29

Бренд: Rangertugs Страницы: 21

2-IN-1 SLIDE & BOUNCE COMBO PARK

Бренд: Banzai Страницы: 8

Wakesetter 20VTX 2019

Бренд: Malibu Boats Страницы: 238

Бренд: Quicksilver Страницы: 47

Бренд: Sea Ray Страницы: 68

Бренд: Sea Ray Страницы: 94

Бренд: Sea Ray Страницы: 32

Бренд: Sea Ray Boats Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды