manualshive.com logo in svg

Sea-doo GTX DI 5649, Руководство оператора

Поделиться
Скачать
Sea-doo GTX DI 5649 Скачать руководство пользователя страница 44

42

Variable Trim System
(if so equipped)

The variable trim system (VTS) chang-
es the angle of the jet pump nozzle to
provide the operator with a fast, effec-
tive system to compensate for load,
thrust, riding position and water condi-
tions. Correctly adjusted, it can im-
prove handling, reduce porpoising, and
position the watercraft at its best
riding angle to attain maximum perfor-
mance.

When first using the watercraft, the
operator should become familiar with
the use of the variable trim system
(VTS) at varying speeds and water con-
ditions. A mid-range trim is generally
used when cruising. Experience alone
will dictate the best trim for the condi-
tions. During the watercraft break-in
period, when lower speeds are recom-
mended, it is an excellent opportunity
to gain familiarity of trim adjustment
and its effects.

When the nozzle is positioned in an up-
ward angle, the water thrust directs the
bow of the watercraft upward. This po-
sition is used to optimize high speed.

TYPICAL

1. Push on arrow pointing upward on VTS

button

2. Bow up
3. Nozzle up

NOTE:

VTS position is indicated on a

bar gauge in the information center.

When the nozzle is directed down-
ward, the bow is forced downward and
enhances the watercraft turning capa-
bilities. As with any watercraft, speed
and operator body position and move-
ment (body English), will determine the
degree and sharpness of the water-
craft turn. Porpoising can be reduced or
eliminated if the nozzle is downward
and speed is adjusted proportionately.

F07L1XY

1

2

3

8°

smo2000-003a.book Page 42 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды