manualshive.com logo in svg

Sea-doo GTX DI 5649, Руководство оператора

Поделиться
Скачать
Sea-doo GTX DI 5649 Скачать руководство пользователя страница 28

26

Message Display

The Information Center features a dis-
play area that blinks a message when-
ever one of the following circumstanc-
es occurs: 

• compass error (COMPAS)

• maintenance (MAINT)

• engine overheating (H-TEMP)

• low fuel (FUEL-LO)

• low oil (OIL LOW)

• low voltage (12 V LOW)

• fuel injection system sensors and

major components (

DI models

)

Except for low fuel and low oil, which
can be corrected by refilling, it is rec-
ommended to see an authorized Sea-
Doo dealer when other messages oc-
cur.

The warning light will blink at the same
time.

Warning Light

The red warning LED (Light-Emitting
Diode) blinks along with the message
display to catch your attention.

Fuel Level Display

Bar gauge continuously indicates the
amount of fuel in the fuel tank while
riding. A low-fuel condition is also indi-
cated when it occurs. See 

Message

Display

 above.

VTS Position Indicator
(if so equipped)

The VTS position indicator shows the
riding angle of the watercraft.

1. Position indicator
2. Bow up
3. Bow down

Display Priorities

The clock, (clock/compass, 

if so

equipped

) is the default display mode.

The default display is the one that ap-
pears when the information center is
first activated or displayed back after
an alternate display was chosen.

The tachometer, speedometer and
chronometer, are the only other modes
that may be chosen to replace the de-
fault display. When one of these is se-
lected, it will become the default dis-
play until it is changed again.

When another display mode is chosen,
the default display will be displayed
back after 4 seconds.

As a self test, all LCD segments and the
LED will turn on for 3 seconds each time
the information center is activated.

In the event of a warning message, the
message will blink and override the
units display.

If more than one warning message oc-
curs, the blinking messages will scroll
every 4 seconds.

F00L2DY

1

2 3

smo2000-003a.book Page 26 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Содержание GTX DI 5649




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды