Sea-doo GTX DI 5649 Скачать руководство пользователя

Страница: 30 / 91

Chronometer

While in the chronometer mode:

1. Press to start or stop chronometer

1. Press and hold for 2 seconds to reset

Maintenance Information

When the watercraft is due for a mainte-
nance inspection, the message MAINT
will blink.

To clear the warning message while it
is blinking:

1. Press and hold for 2 seconds to reset

N O TE :

If ma in te n an ce me ss ag e

(MAINT) continues to blink, it indicates
a fault with the fuel injection system on

Di models

. Refer to an authorized Sea-

Doo Dealer for servicing.

10) Glove Box

A small, convenient storage compart-
ment for personal articles.

11) Fuel Tank Valve

Carburetor-Equipped Models

A 3-position rotating valve: OFF, ON
and RESERVE:

OFF: Stop fuel supply to carburetor(s).

CAUTION:

Turn valve to OFF posi-

tion when

watercraft

is not operated.

ON: Allows fuel to flow to carbure-

tor(s). This is the normal position
for operation of watercraft.

CAUTION:

Improper opening of fuel

valve may restrict flow of fuel and
may lead to engine damage. Make
sure valve is fully opened while run-
ning.

RES: Use when the watercraft has run

out of fuel in the ON position.

Always refill the fuel tank at the first
opportunity. After refueling, turn the
fuel tank valve to the ON position to
continue operation.

12) Fuel Tank Cap

Open the front storage compartment
cover to expose fuel tank cap.

The tank cap is located on the left hand
side of the watercraft.

Unscrew the cap counterclockwise. Af-
ter fueling, reinstall cap and fully tighten.

13) Oil Injection Reservoir

Cap

Open the front storage compartment
cover to expose reservoir cap.

The reservoir cap is located on the right
hand side of the watercraft.

To add injection oil in the reservoir, un-
screw the cap counterclockwise. Do not
overfill. Reinstall cap and fully tighten it.

F00L2B0



WARNING

Never use a lit match or open flame
to check fuel level.

smo2000-003a.book Page 28 Thursday, November 11, 1999 10:44 AM

www.SeaDooManuals.net

Содержание GTX DI 5649




























































































Результаты поиска

Содержание GTX DI 5649

Отзывы:

Похожие инструкции для GTX DI 5649

Бренды по названию

Популярные бренды

Sea-doo GTX DI 5649, Руководство оператора

Результаты поиска

Содержание GTX DI 5649

Отзывы:

Похожие инструкции для GTX DI 5649

Бренды по названию

Популярные бренды