Scientific SM6026 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 95

background image

User Manual SM6026

86

The CORRection:SPOT<n>:STATe command is used to set the state of some specific frequency spots.
The CORRection:SPOT<n>:STATe query returns the current state of each frequency spot (FREQ 1,
FREQ 2 or FREQ 3).
Command syntax:

ON

CORRection:SPOT<n>:STATe

OFF
1
0

Where,

1 (decimal 49) is equal to ON.
0 (decimal 48) is equal to OFF.
<n>:
1 refers to frequency spot 1.
2 refers to frequency spot 2.
3 refers to frequency spot 3.

For example: WrtCmd (“CORR:SPOT1:STAT ON”)

Query syntax: CORRection:SPTO<n>:STATe?
Return format: <NR1><NL^END>

The CORRection:SPOT<n>:FREQuency command is used to set the frequencies of frequency spots1, 2
and 3. The CORRection:SPOT<n> query returns the current frequency of specific frequency spot.
Command syntax: CORRection:SPOT<n>:FREQeuency<value>
Where,
<value> can be NR1, NR2 or NR3 data format followed by HZ, kHz and MHZ.
<n>:
1 refers to frequency spot 1.
2 fefers to frequency spot 2.
3 refers to frequency spot 3.

For example: WrtCmd (“CORR:SPOT1:FREQ 2KHZ”) Set the frequency of frequency spot 1 as 2KHZ.

NOTE: <value> should be ranged from 20HZ to 300KHZ (SM6026 A), or return format will report
errors.

Query syntax: CORRection:SPOT<n>:FREQuency?
Return format: <NR3><NL^END>

The CORRection:SPOT<n>:OPEN command is used to execute open correction for specific frequency
spots (frequency 1, frequency 2 and frequency 3).
Command syntax: CORRection:SPOT<n>:OPEN
Where,
<n>:
1 refers to frequency spot 1.
2 refers to frequency spot 2.
3 refers to frequency spot 3.
For example: WrtCmd (“CORR:SPOT1:OPEN”) Execute open correction for frequency spot 1.

The CORRection:SPOT<n>:SHORt command is used to execute short correction for specific frequency
spots (frequency 1, frequency 2 and frequency 3).
Command syntax: CORRection:SPOT<n>:SHORt

«
...
84
85
86
87
88
...
»

Содержание SM6026
































































































Отзывы:

Нет отзывов

Похожие инструкции для SM6026

Бренд: TaiDoc Страницы: 31

Blancett B3100 Series

Бренд: Badger Meter Страницы: 16

Бренд: Badger Meter Страницы: 26

Бренд: Badger Meter Страницы: 48

Бренд: F&F Страницы: 2

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 38

Бренд: Yamaha Страницы: 45

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды