SBS AT10.1 SERIES Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 104

background image

SERVICING THE AT10.1

59

Replacing the Main Control (A1) and/or Gate Driver (A11) PC Boards

For details of this procedure, refer to

Service Instruction

(

JD5012-00

).

NOTICE

Printed circuit boards are sensitive to damage from static discharges. Leave
replacement boards in their anti-static bags until you are ready to install them.

Ground yourself before handling the board, by touching the ground stud on the
back of the door. Always handle printed circuit boards by their edges.

Shut down and lock out all power to the AT10.1. Disconnect the battery
from the output terminals. Remove any optional user wiring from the
various Main Control PC Board (A1) terminals (e.g. TB3, TB8/J6, J3,
etc.).

Note that A1 and A11 are mounted together as a pair. Remove the signal
wire harness plug (J18) at the left edge of A11. The boards are mounted
on ten (10) plastic standoffs. Compress the tab on each standoff, and pull
the boards toward you until they clear all the standoffs. If you are
replacing only one board, carefully separate the existing boards (A1 &
A11) and reconnect the replacement board.

Insert the replacement board(s) onto the instrument panel with the same
orientation, and push them onto the standoffs. Make sure the board is
fully seated on all ten (10) standoffs. Reconnect the signal wire harness
plug (J18) to the Gate Driver PC Board (A11), matching the orientation
when removed. Replace any user wiring to the various Main Control PC
Board (A1) terminals.

See Section 2.1 for the steps to restart the AT10.1. If your AT10.1
parameters (float voltage, etc.) are different from the factory preset values,
you should program in the new values now. See Section 2.3. You should
also recalibrate the dc voltmeter according to Section 2.3.7.

Replacing the ac input or dc output circuit breaker (CB1/CB2)

Shut down and lock out all power to the AT10.1. Remove the Plexiglas
safety shield. Disconnect the battery from the dc output terminals
(TB1+/-). This includes remote sense wires if they were installed.
Check with a voltmeter before proceeding. Remove the mounting screws
for the circuit breaker on the galvanized mounting bracket. Carefully
remove the wired circuit breaker from the AT10.1.

Remove wires from the terminals, one at a time, and transfer the wires to
the terminals of the replacement breaker.

Confirm all circuit breaker

terminal screws are tight

.

Install the replacement breaker into the

mounting bracket, reversing the procedure above, using the original
mounting screws.

«
...
63
64
65
66
67
...
»

Содержание AT10.1 SERIES









































































































Отзывы:

Нет отзывов

Похожие инструкции для AT10.1 SERIES

Бренд: GARO Страницы: 43

Бренд: Camelion Страницы: 6

Бренд: Hama Страницы: 75

2608A-B-01 Trolling Charger Series

Бренд: Guest Страницы: 7

Бренд: Targus Страницы: 4

Бренд: iLive Страницы: 8

JG-4IFR12.8-150-Y

Бренд: ENERpower Страницы: 10

eVault Max 18.5

Бренд: Fortress Power Страницы: 2

Бренд: Parkside Страницы: 45

Бренд: S.P.E. Страницы: 64

Бренд: LXE Страницы: 60

Бренд: EINHELL Страницы: 28

Бренд: Duramaxx Страницы: 140

Бренд: Fellowes Страницы: 16

Бренд: Silvercrest Страницы: 56

Бренд: Motorola Страницы: 27

Бренд: hager Страницы: 4

Бренд: Milwaukee Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды