SBS AT10.1 SERIES Скачать руководство пользователя страница 37

Страница: 37 / 104

OPERATING THE AT10.1

2.3.2. Setting the Float and Equalize voltages

•

Press the

EDIT/ENTER

key.

The

FLOAT

and

DC VOLTS

indicators light, and the display flashes the

present value of the float voltage. Press and release the

DOWN

key to

increase or decrease the value in the display by one count, or press and
hold the

DOWN

key to scroll the value in the display upward or

downward. When the meter displays the desired float voltage, release the

DOWN

key. If you go past the voltage you want, press the

DOWN

key again to reach the voltage you want to set.

•

Press the

EDIT/ENTER

key. The new float voltage setting is saved

internally.

The

EQLZ

and

DC VOLTS

indicators light, and the display flashes the

present value of the equalize voltage. Press and release the

DOWN

key to increase or decrease the value in the display by one count, or press
and hold the

DOWN

key to scroll the value in the display upward or

downward. When the meter displays the desired equalize voltage, release
the

DOWN

key. If you go past the voltage you want, press the

DOWN

key again to reach the voltage you want to set.

•

Press the

EDIT/ENTER

key. The new equalize voltage setting is saved

internally.

If you want to adjust the equalize timer duration, skip to Section 2.3.3.

If you want to exit the

Edit Mode

now, press the

EDIT/ENTER

key four (4)

more times until the AT10.1 returns to normal operation.

If you do not press any front panel key for 25 seconds,

Edit Mode

ends

automatically, and any change you made to the last setting is not saved.

Содержание AT10.1 SERIES









































































































Результаты поиска

Содержание AT10.1 SERIES

Отзывы:

Похожие инструкции для AT10.1 SERIES

Бренды по названию

Популярные бренды

SBS AT10.1 SERIES, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание AT10.1 SERIES

Отзывы:

Похожие инструкции для AT10.1 SERIES

Бренды по названию

Популярные бренды