SBS AT10.1 SERIES Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 104

background image

SERVICING THE AT10.1

52

SYMPTOM

PROBABLE

CAUSE

RECOMMENDED ACTION

Front panel is
dead, but ac
& dc voltages
are present at
TB1(+/-)

1. Control pc
boards
(A1/A11) not
connected

2. Defective
Main Control
PC Board (A1)

3. Defective
wiring

1. Confirm the

Gate Driver PC B

oard (A11-P17) is firmly

connected to the Main Control PC Board (A1-J17). Confirm
the signal harness plug is firmly inserted into the

Gate Driver

PC Board

connector (J18).

2. If the green

AC ON

indicator is lit, but the rest of the front

panel display is dead, replace the Main Control PC Board
(A1).

3. Check the harness wiring to the Gate Driver PC Board
connector (A11-J18), for signs of insulation damage, burns,
etc. Confirm all wires are securely crimped in the connector.

Front panel
dies during ac
power failure,
but dc voltage
is present at
TB1(+/-)

1. Defective
Power Supply
Ballast Resistor
(R3)

2. Defective
wiring

1. Use a dc voltmeter to measure voltage from TB1(-) to J1 pin
#

8

on the Main Control PC Board (A1). It is normally 12 Vdc

when the rated dc output voltage is present at TB1(+/-).

If it is

not

12 Vdc, remove all power from the AT10.1 and

measure the resistance of R3, from TB1(+) to J1 pin #

8

. See

the table in Section 3.6 for the proper resistance value. If the
resistance is not within 10% of the table value, replace R3.

2. Remove the clear safety shield. Check the wiring to and
from TB1 and the Main Control PC Board (A1) for signs of
insulation damage or burns. Repair any damaged wiring.

AT10.1
output
voltage too
high, or not
controllable

1. Defective
SCR

2. Defective or
wrong value
scaling resistor
(R4 or R14)

3. Defective
temperature
compensation
probe (optional)

4. Defective
Main Control
PC Board (A1)

1. Disconnect the twisted pair wires #

51/52

and #

53/54

from

the SCR (Q1/Q2) gate lead terminals. Note the original
polarity so wires can be replaced with the same orientation.
Restart the AT10.1. If you are able to measure output current,
one of the SCRs is defective. Replace SCR modules (Q1/Q2)
as needed.

2. On the back of the front panel, locate R4 and R14 on the
Gate Driver PC Board (A11). Remove one end of each
resistor and measure its value with an Ohmmeter. Refer to
the table in Section 3.6 for values. If either resistor is not
within 1% of the specified value, replace the scaling resistors
(R4 and/or R14) as needed.

3. Remove the leads from the probe and measure its
resistance. At 77 °F / 25 °C the resistance should be about
10,000

Ω

. If it is not, replace the probe assembly (A10).

4. If the front panel meter displays more than 110% of the
AT10.1 rated dc current, the Main Control PC Board (A1) may
be defective. Unplug the system harness connector (J18) from
the Gate Driver PC Board (A11). If the output current drops to
zero (Adc), replace the Main Control PC Board (A1).

«
...
56
57
58
59
60
...
»

Содержание AT10.1 SERIES









































































































Отзывы:

Нет отзывов

Похожие инструкции для AT10.1 SERIES

Бренд: EBL Страницы: 51

Бренд: Parallel Audio Страницы: 4

Бренд: GARO Страницы: 43

Бренд: Datalogic Страницы: 2

Бренд: Gardena Страницы: 13

Бренд: Napa Страницы: 32

EVduty EVC30 Series

Бренд: Elmec Страницы: 26

Бренд: Turbot Страницы: 3

Wallbox Home 11 kW

Бренд: WINDSY Страницы: 31

Бренд: Könner & Söhnen Страницы: 6

Pocket Power StarLight 2800

Бренд: Halo2Cloud Страницы: 10

Бренд: Patriot Страницы: 28

Бренд: akkuteam Страницы: 76

Eve Plus 0131-CC

Бренд: Basalte Страницы: 2

Бренд: APA Страницы: 32

Бренд: Tactical Страницы: 2

BATTERY CHARGER PLUS EEBC500B

Бренд: Snap-On Страницы: 55

Бренд: KAFULLE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды