SBS AT10.1 SERIES Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 104

background image

RECEIVING THE AT10.1

2

1. RECEIVING THE AT10.1

1.1. STORING THE AT10.1

If you store the AT10.1 for more than a few days before installation, you
should store it in its original shipping container, and in a temperature
controlled, dry climate. Ambient temperatures of 0 to 122 °F / -18 to 50
°C are acceptable. Storage should not exceed two (2) years due to the
limited shelf life of the dc filter capacitors when they are not in service.

1.2. REPORTING SHIPPING DAMAGE

Upon delivery of the AT10.1 (or related products) if you discover any
damage or shortage, make notation on all copies of delivering carrier's
delivery receipt before signing and notify the delivery person of your
findings. If loss or damage is discovered after delivery, notify delivering
carrier immediately and request an inspection. The manufacturer does not
assume any liability for damage during transportation or handling.

Should the products require an inspection by (or return to) the
manufacturer, please contact your sales representative for further
instructions. Any returned material must be properly packed in
compliance with shipping regulations. It is preferable to use the original
shipping materials if possible. Mark the outside of the shipping container
with the Return Material Authorization (RMA) number issued by the
manufacturer.

1.3. UNPACKING AND INSPECTING THE AT10.1

Carefully remove all shipping materials from the AT10.1. Remove the
AT10.1 from the shipping pallet for inspection. Save all shipping
materials until you are sure that there is no shipping damage.

Once the AT10.1 is unpacked, inspect the unit for possible shipping
damage, using the checklist below. If shipping damage has occurred, refer
to Section 1.2 on this page for proper reporting.

INSPECTION CHECKLIST

Enclosure exterior and interior are not marred or dented.

There is no visible damage to exterior or interior components.

All internal components are secure.

Printed circuit boards are firmly seated on their standoffs.

All hardware is tight.

All wire terminations are secure.

The User's Manual is included.

You received all items on the packing list.

«
...
6
7
8
9
10
...
»

Содержание AT10.1 SERIES









































































































Отзывы:

Нет отзывов

Похожие инструкции для AT10.1 SERIES

Бренд: ABL Страницы: 30

Бренд: ABL Страницы: 176

Бренд: ABL Страницы: 94

Бренд: ABL Страницы: 34

Бренд: SUEX Страницы: 40

Бренд: Energic Plus Страницы: 27

Charge powerdry

Бренд: Miracle-Ear Страницы: 49

Бренд: fontastic Страницы: 2

Бренд: Kodak Страницы: 24

Бренд: xtorm Страницы: 36

Бренд: VOLTCRAFT Страницы: 14

Бренд: Saitek Страницы: 15

Fontastic FORT 22

Бренд: D-Parts Страницы: 2

Бренд: P.I.T. Страницы: 25

Бренд: LTC Страницы: 19

CK1 Serial Dock

Бренд: Intermec Страницы: 147

Power Peak Infinity 3

Бренд: ROBBE Страницы: 160

Бренд: Black & Decker Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды