SBS AT10.1 SERIES Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 104

background image

SERVICING THE AT10.1

60

Replacing the ac surge suppressors (VR2, VR4 or VR5)

Shut down and lock out all power to the AT10.1. Open the door and
remove the safety shield. Disconnect the battery from the output
terminals.

For

VR2

, remove the hardware from the input terminal L1, and remove

the lead of the ac surge suppressor. Install one lead of the replacement
surge suppressor onto the L1 terminal. Replace the other wires and the
hardware. Repeat procedure for the L2 terminal. Tighten all hardware.

For

VR4

, remove the hardware from the input terminal L1, and remove

the lead of the ac surge suppressor. Install one lead of the replacement
surge suppressor onto the L1 terminal. Replace the other wires and the
hardware. Repeat procedure for the

left

ground stud. Tighten all

hardware.

For

VR5

, repeat procedure for the ac surge suppressor connected to the L2

terminal and the

right

ground terminal. Tighten all hardware.

NOTICE

The ac surge suppressors are not polarized.

Replacing the dc surge suppressor (VR1)

Shut down and lock out all power to the AT10.1. Open the door and
remove the safety shield. Disconnect the battery from the output
terminals.

Remove the hardware from the output terminal TB1(+), and remove the
lead of the dc surge suppressor. Install one lead of the replacement surge
suppressor. Replace the other wires and the hardware. Repeat for the
output terminal TB1(-). Tighten all hardware.

NOTICE

The dc surge suppressor is not polarized.

Replacing the dc EMI filter networks (VR6/C4, VR7/C5)

Replace these networks as assemblies. Do not replace individual parts.

Shut down and lock out all power to the AT10.1. Open the door and
remove the safety shield. Disconnect the battery from the output
terminals.
To replace the network VR6/C4, remove the hardware from the output
terminal TB1(-), and remove the lead of the network. Cut the plastic wire
ties holding the assembly tight against the I/O panel. Install one lead of
the replacement network. Replace the other wires and the hardware.
Repeat for the other lead of the network on the ground terminal. For the
network VR7/C5, use the above procedure, but start with the lead on
TB1(+). Tighten all hardware. Replace cut wire ties if possible.

NOTICE

The dc EMI filter networks are not polarized.

«
...
64
65
66
67
68
...
»

Содержание AT10.1 SERIES









































































































Отзывы:

Нет отзывов

Похожие инструкции для AT10.1 SERIES

Бренд: XTAR Страницы: 2

Бренд: XD COLLECTION Страницы: 10

VTEC X-treme Race-1S-3.7V

Бренд: Nosram Страницы: 4

Бренд: Tesla Страницы: 3

Бренд: Kodak Страницы: 24

Бренд: Metabo Страницы: 16

Бренд: Stanley Страницы: 156

Бренд: MPS Страницы: 8

Бренд: Laser Страницы: 6

Бренд: HardWire Страницы: 18

Бренд: ABB Страницы: 132

Бренд: ABB Страницы: 132

MSW-CBC-105W-6A

Бренд: MSW Motor Technics Страницы: 11

Бренд: Makita Страницы: 144

Бренд: Myenergi Страницы: 42

Бренд: Myenergi Страницы: 51

Бренд: Bolt Страницы: 32

Бренд: Silvercrest Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды