GROUP S.P.A.
MT SBC 01
68
Extreme temperatures can affect the charging capacity of the
batteries.
Never use damaged batteries or battery chargers.
Do not short-circuit the batteries. This can happen accidentally if,
for example, you keep a spare battery in your pocket or a container
with another metal object, which may bring the + and – terminals of
the battery into direct contact, thus damaging the battery or the
object in question.
Display
Hand-held programmer Art. 1251/A is equipped with a graphic
display with resolution of 128x64 dots/pitch.
The display has a timed lighting system for saving energy, which
is especially useful when running the module on batteries.
The lighting switches off automatically about 30 seconds after the
last keystroke: it switches back on as soon as any key on the
programmer is pressed.
Display brightness control
The brightness of the display can be adjusted by means of a
trimmer inside the programmer.
You must therefore open the programmer and proceed as follows
(figure 9):
1. Unscrew the 6 screws on the back of the programmer.
2. Keep the cover raised with the keypad and turn trimmer TM1:
- clockwise to reduce brightness
- anti-clockwise to increase brightness.
3. Make sure that the membrane keypad is still connected to the
ZIF connector.
4. Screw the cover back onto the base.
12V
D
C
+
--
. , :
F1
F2
F3
F4
1
2
3
4
5
6
7
8
9
*
0
#
ABC
DEF
GH
I
MN
O
PQ
RS
WX
YZ
JK
L
TU
V
Fig. 9
Standby mode
When the hand-held programmer is ready for use but the user has
not connected any device by serial cable, the module is in standby.
In standby, the
and
keys are available. The display
shows the name Comelit and a moving logo (see figure 1).
It is possible to go back into standby when you are connected to a
device, by pressing
several times until the Comelit logo
appears on the display.
Setting the language
From standby mode, press
to access the language menu.
Use the
and
keys to scroll the menu and display the
9 available languages;
After selecting the language, press
to confirm and go back
into standby.
Connecting the programmer to the device to be
configured
To programme a device, connect the programmer to the device by
means of the programming cable provided with the programmer.
The programmer automatically recognises the device connected and
therefore only enables the functions which can be programmed on
that device.
Connecting the programmer to Art. 5714C, 5714CI, 4784, 4784I,
2618 and 2418W
Proceed as follows:
1. Make sure the bracket (or interphone) is not connected to the
system.
2. Switch on hand-held programmer Art. 1251/A with the
programming cable connected to the programmer.
Ok
Opt
Esc
Sel
Opt
. , :
F1
F2
F3
F4
1
2
3
4
5
6
7
8
9
*
0
#
AB
C
DE
F
GH
I
MN
O
PQ
RS
W
XY
Z
JK
L
TU
V
ON
OF
F
CN
1
Fig. 10
Содержание MT 01
Страница 17: ...MT SBC 01 15 MT SBC 01 U P yellow green A L T O A L T O MIC U P U P 8 9 10 11 12 13...
Страница 18: ...GROUP S P A MT SBC 01 16 U P UP U P UP ALTO UP 1 2 P U P 14 15 16 SOLUTION A SOLUTION B...
Страница 30: ...GROUP S P A MT SBC 01 28 1 6 7 2 3 4 5 Installation instructions for N AV 4 audio external unit yellow green...
Страница 41: ...MT SBC 01 39 MT SBC 01 2 3 1 6 5 4 6 Mounting the monitor on desktop base Art 5712...
