Samsung SRN-1000 Скачать руководство пользователя страница 79

Страница: 79 / 122

English

_79

●

enu Se

Tup

SeTTing The evenT

You can make the setup for record in case of sensor detection, camera event or video loss detection.

Sensor detection

You can set the sensor's operating condition and connected camera, as well as alarm output and its duration.

Setting nvr Sensor detection

•

Sensor Operation : Sets the operation mode of sensors.

- <

n.o (normal open)

> : Sensor is opened. If the sensor is closed, it generates alarm.

- <

n.C (normal Close)

> : Sensor is closed. If the sensor is open, it generates alarm.

•

Cam : Select a channel to be connected to the sensor.

If selected camera, "

Cam preset setup

" window appears.

Select a channel and setup the preset.

Preset setup can be done in PTZ mode.

•

Alarm out : Sets the alarm output method.

For further information on alarm output, refer to "

HDD Alarm Setting

". (Page 74)

•

Duration : Sets the duration of alarm signal and alarm sound.

Содержание SRN-1000



























































































































Результаты поиска

Содержание SRN-1000

Отзывы:

Похожие инструкции для SRN-1000

Бренды по названию

Популярные бренды

Samsung SRN-1000, Руководство пользователя

Результаты поиска

Содержание SRN-1000

Отзывы:

Похожие инструкции для SRN-1000

Бренды по названию

Популярные бренды