Samsung CLX-9251 Series Скачать руководство пользователя страница 210

Страница: 210 / 481

4. Troubleshooting

Code

Display

Meaning

100-0380

Tray2 Pickup Motor

Tray2 Motor is On/Off

100-0390

Tray3 Pickup Motor

Tray3 Motor is On/Off

100-0400

Tray4 Pickup Motor

Tray4 Motor is On/Off

100-0430

Exit2 Motor Forward

Exit2 Motor is On/Off

100-0440

Exit2 Motor Backward

Exit2 Motor is On/Off

100-0450

ITB Motor

ITB Motor is On/Off

100-0460

Ready ITB

Detect if ITB Motor runs at normal speed

100-0470

DCF Feed Motor

DCF Feed Motor is On/Off

101-0000

Bypass Feed Clutch

Engages drive to pick up a paper from bypass Tray(MP
Tray).

101-0050

Registration Clutch

Engages drive to registartion rolls.

101-0190

Out-Bin Full Sensor

Detect when a paper is at Out-Bin Full Sensor

101-0191

Out-Bin2 Full Sensor

Detect when a paper is at Out-Bin2 Full Sensor

101-0270

MP Clutch

MPClutch On/Off

101-0271

MP Solenoid

MP Solenoid On/Off

101-0280

Return Gate Solenoid

Return Gate Solenoid On/Off

102-0000

Tray1 Home Position

Detect when tray1 is closed.

102-0010

T1 Paper Empty Sensor

Detect when paper is in Tray1.

102-0041

T1 Paper Size Read

Detects Paper Tray1 size.

102-0050

T1 Stack Height Sensor

Detects if paper in tray1 is elevated to the sensor.

102-0070

Tray2 Home Position

Detect when tray2 is closed.

102-0080

T2 Paper Empty Sensor

Detect when paper is in tray2.

102-0111

T2 Paper Size Read

Detects Paper Tray2 size.

102-0120

T2 Stack Height Sensor

Detects if paper in tray2 is elevated to the sensor.

102-0140

Tray3 Home Position

Detect when tray3 is closed.

102-0150

T3 Paper Empty Sensor

Detect when paper is in tray3.

102-0181

T3 Paper Size Read

Detects Paper Tray3 size.

102-0190

T3 Stack Height Sensor

Detects if paper in tray3 is elevated to the sensor.

102-0210

Tray4 Home Position

Detect when tray4 is closed.

102-0220

T4 Paper Empty Sensor

Detect when paper is in tray4.

102-0251

T4 Paper Size Read

Detects Paper Tray4 size.

102-0260

T4 Stack Height Sensor

Detects if paper in tray4 is elevated to the sensor.

102-0280

Bypass Paper Empty Sensor

Detects when paper is in Bypass Tray(MP Tray).

102-0290

Feed Sensor

Detect when a paper is at Feed sensor.

102-0300

T2 Feed Sensor (or Door Open)

Detect when a paper is at T2 Feed sensor. (optional)

102-0320

T3 Feed Sensor (or Door Open)

Detect when a paper is at T3 Feed sensor. (optional)

102-0340

T4 Feed Sensor (or Door Open)

Detect when a paper is at T4 Feed sensor. (optional)

102-0352

DCF Feed Cover Open

Detect DCF Cover is closed

102-0360

Regi. Sensor

Detect when a paper is at Regi. sensor.

102-0361

FuserOut Sensor

Detect when a paper is at FuserOut sensor.

102-0371

Exit2 Sensor

Detect when a paper is at Exit2 sensor.

4-25

Содержание CLX-9251 Series
























































































































































































































































































































































































































































































Результаты поиска

Содержание CLX-9251 Series

Отзывы:

Похожие инструкции для CLX-9251 Series

Бренды по названию

Популярные бренды

Samsung CLX-9251 Series, Руководство по обслуживанию

Результаты поиска

Содержание CLX-9251 Series

Отзывы:

Похожие инструкции для CLX-9251 Series

Бренды по названию

Популярные бренды