Saluki S1465 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 243

background image

Tel: 886.909 602 109 Email: [email protected]

www.salukitec.com

36

agents.
2)

Cleaning of display

After the instrument is used for a period of time, it is necessary to clean the LED. Please operate

according to the following steps:

Step 1. Power off the instrument, and disconnect the power cord from the instrument;
Step 2. Use clean soft cotton cloth dampened with cleaning agents to gently wipe the display

panel;
Step 3. Dry the display with clean soft cotton cloth;
Step 4. Connect the power cord after the display is dried completely.

CAUTION

Clean the display

There is a layer of ESD protection coating on the surface of the display, so never use any

cleaning agent containing fluoride, acid or alkali. Do not spray the cleaning agent directly onto the

display panel, otherwise the cleaning agent may leak into the internal of the instrument, causing

damages.

2.1.3.2 Maintenance of testing port

The front panel of S1465 series signal generator has a type N (female) or 3.5mm/ 2.4mm/

1.85mm (male) port and several BNC ports (female). A damaged connector or dust inside will affect

RF band test result. Therefore, maintain such connectors in a manner as described below:



Connectors shall be kept clean and away from dust;



To prevent ESD, do not directly contact the connector surface;



Do not use a damaged connector;



Clean connectors with a dryer, and do not grind the surface with a tool like abrasive paper.

CAUTION

Impedance matching of ports

The front RF ports for S1465 series signal generator are 50Ω type-N (female) or

3.5mm/2.4mm/1.85mm (male) connectors. Using a connector with unmatched impedance will cause

damage to it.

2.2 Description of front and rear panels

This section presents the composition and functions of front and rear panels for the S1465 series

signal generator.

2.2.1 Description of front panel

This section introduces the composition and functions of front panel of S1465 series signal

generator, which is illustrated below (Fig.2.11) and itemized in Table 2.5:

«
...
34
35
36
37
38
...
»

Содержание S1465 Series




















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1465 Series

Бренд: Panasonic Страницы: 7

Бренд: Champion Power Equipment Страницы: 38

Бренд: BE Страницы: 56

Бренд: Generac Power Systems Страницы: 56

Бренд: Daewoo Страницы: 91

Бренд: QFX Страницы: 11

Бренд: Titan Страницы: 23

Бренд: Com-Power Страницы: 15

Бренд: Bearcat Страницы: 14

Бренд: Yamato Страницы: 48

ITD 4 +KTD 3-1 B10 Series

Бренд: Baumer Страницы: 20

Бренд: QUANTUN Страницы: 24

Бренд: QuantumFX Страницы: 72

Бренд: GoVideo Страницы: 1

Бренд: Oras Страницы: 2

Public Alert WX-150

Бренд: First Alert Страницы: 16

Бренд: Aim-TTI Страницы: 211

Бренд: E.F. Johnson Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды