manualshive.com logo in svg

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 30 / 288

Поделиться
Скачать
Sailor 250 FleetBroadband Скачать руководство пользователя страница 30

Chapter 1:  Introduction

14

The Inmarsat BGAN system

Circuit-Switched (dialed) service

The following types of circuit-switched connection are available:

•

Standard Voice.

 A low-tariff connection for voice only. The voice signal is 

compressed to 4.0 kbps, which reduces the bandwidth use and 
consequently the tariff.

•

3.1 kHz Audio

. A high quality connection which can be used for Premium 

Voice or G3 fax. The signal is uncompressed 3.1 kHz audio, which allows for 
optimum voice quality.

•

ISDN.

 A high quality connection which can be used for voice (3.1 kHz 

Audio), G4 fax or 64 kbps UDI/RDI data.

SMS service

The BGAN system provides a Short Messaging Service (SMS) for sending and 
receiving SMS messages to and from the terminal.

Multi-voice service (optional)

Normally, the BGAN system only supports one call at a time per 
SAILOR FleetBroadband system. When you subscribe to the optional Multi-
voice service and enable it in your system, you can have up to 9 concurrent 
calls.

To use the Multi-voice service you must enable Multi-voice and enter the APN 
for Multi-voice in the web interface of the SAILOR FleetBroadband terminal. 
For information on how to set up Multi-voice, see 

Multi-voice

 on page 196.

Voice Distress service (optional)

The Voice Distress service uses FleetBroadband to provide priority call access 
as soon as the red distress button on the alarm panel is pressed. The caller 
will then be connected to an operator at one of three Maritime Rescue 
Coordination Centres (MRCCs) strategically located around the globe.

To use the Voice Distress service you must first have it included in your airtime 
subscription, acquire a SAILOR 3771 Alarm Panel, enable Voice Distress in your 

Содержание 250 FleetBroadband

































































































































































































































































































Отзывы:

Нет отзывов