Sailor 250 FleetBroadband Скачать руководство пользователя страница 245

Страница: 245 / 288

Chapter 5: Troubleshooting

Status signalling

229

555

ouble

sho

ing

02000
to
02009

Satellite

signal weak

The signal from the
satellite is weak.

Check the line of
sight to the satellite.

Check in the web
interface under

SETTINGS > Satellite
selection

that you

have selected

Auto

or a satellite
covering your
current position.

02100 to
02109

Ciphering Off

The network has
turned ciphering
off.

Do not transmit data
that requires
ciphering.

02200 to
02209

Ethernet data

session failed

Ethernet data
session could not be
established.

See the call log for
the cause of the
error. Refer to

Viewing the lists of
calls and data
sessions

page 97.

If the problem
persists, contact
your distributor.

02900
to 02909

Network failed

authentication

The SAILOR system
does not accept the
network as a valid
BGAN network.

Restart the SAILOR
system.

If the problem
persists, contact
your distributor.

Event Text

Explanation

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 245 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: