Sailor 250 FleetBroadband Скачать руководство пользователя страница 255

Страница: 255 / 288

Chapter 5: Troubleshooting

Status signalling

239

555

ouble

sho

ing

08064

No connection

FleetBroadband

Alarm Panel

The system is
configured for Voice
Distress but there is
no connection
between the
terminal and the
SAILOR 3771 Alarm
Panel

Check that the
alarm panel is
connected correctly
to the terminal. See
the installation
manual for the
Voice Distress (Non-
SOLAS) system.

08065

Voice Distress

Supplementary

Service

(eMLPP)

subscription

failure

Voice Distress
registration fails.
The service has not
been enabled on
your SIM card.

Contact your service
provider and
request that Voice
Distress is enabled
in your SIM card.

08066

Voice Distress

Supplementary

Service (Call

Waiting)

subscription

failure

The FleetBroadband
terminal is not able
to activate the Call
Waiting service in
the network.

Check with your
service provider that
the Call Waiting
service is
commissioned.

0806E

Voice Distress

is disabled

Voice Distress has
been disabled - the
Voice Distress
service will not
work.

The service can be
reenabled in the
web interface of the
FleetBroadband
terminal.

Event Text

Explanation

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 255 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: