Sailor 250 FleetBroadband Скачать руководство пользователя страница 256

Страница: 256 / 288

Chapter 5: Troubleshooting

240

Status signalling

08079

Multi-voice

control

connection

error

Not possible to
establish
connection to Multi-
voice server

Check that Multi-
voice is included in
your subscription.

Check that the
Multi-voice APN
entered in the web
interface under

ADMINISTRATION >
Multi-voice

matches

the Multi-voice APN
from your airtime
subscription

0807C

Multi-voice

failed

Not possible to
register on the
Multi-voice server

Check that Multi-
voice is included in
your airtime
subscription.

0900A

Antenna -

Write

verification

fault in

EEPROM

An EEPROM is
defective or the
EEPROM
communication
fails. The antenna is
unable to save the
last known
frequency and
elevation after
entering track state.
If the EEPROM is
defective, data may
be lost or
inaccessible.

Power cycle the
system. If the fault
persists, contact
your distributor.

Event Text

Explanation

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 256 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: