Sailor 250 FleetBroadband Скачать руководство пользователя страница 230

Страница: 230 / 288

Chapter 5: Troubleshooting

214

Troubleshooting guide

No phones are
ringing on
incoming calls

The Mute function is
activated from an
external device
connected to the I/O
interface of the
terminal.

If the Mute function should not be
activated, deactivate it from the
external device.

The call types for the
handset interfaces
are not set up
correctly.

Check the call types for your handset
interfaces. See

Selecting the call type

on page 45.

If you have Multi-
voice, see the
following entry in
this table:

Multi-

voice: Voice call is
not put through

See the following entry in this table:

Multi-voice: Voice call is not put
through

Problem

Possible Cause

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 230 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: