Sailor 250 FleetBroadband Скачать руководство пользователя страница 252

Страница: 252 / 288

Chapter 5: Troubleshooting

236

Status signalling

08046

Timeout of

startup

sequence - No

antenna or

antenna

temperature

too low

The start-up
sequence of the
terminal has timed
out because:

•

the antenna is
not properly
connected, or

•

the antenna
temperature is
too low to start
up.

Check that the
antenna cable is
properly connected
at both ends.

08048

All PoE ports

except port 1

are shut down

due to high

temperature

The temperature in
the terminal is too
high. All PoE ports
except port 1 are
shut down to reduce
the temperature.

Move the terminal
to a cooler location,
or avoid using PoE
on port 2-4.

08049

Data rate

reduction due

to high

temperature

The bit rate of the
data channel is
reduced because
the temperature is
too high.

Move the terminal
to a cooler location

0804B

Illegal

combination of

antenna and

terminal

You are not using
the right
combination of
antenna and
terminal.

Only use the
antenna(s) intended
for use with your
terminal.

Event Text

Explanation

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 252 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: