Sailor 250 FleetBroadband Скачать руководство пользователя страница 248

Страница: 248 / 288

Chapter 5: Troubleshooting

232

Status signalling

0800B

PoE

Overvoltage

protection is

activated

Overvoltage is
detected in the
terminal. The
terminal will be
shut down in 10
minutes.

Do not use the
terminal.

Contact your
distributor.

0800D

Antenna

Overvoltage

protection is

activated

Overvoltage is
detected in the
antenna. The
terminal will be
shut down in 10
minutes.

Do not use the
terminal.

Contact your
distributor.

08010

Undervoltage

has been

detected

The input voltage
has dropped below
an acceptable level.
The terminal will be
shut down in 10
seconds if the
situation persists.

Ensure a stable
power supply to the
terminal.

0801B

Lost

connection to

the GPS

receiver

Communication
with the GPS
receiver in the
antenna is lost.

Contact your
distributor if the
warning persists.

0801D

Uploading

firmware to

antenna

New firmware is
being uploaded to
the antenna.

The Event will be
cleared when
upload has finished.

Contact your
distributor if the
Event is not cleared
within 5 minutes.

Event Text

Explanation

Remedy

Содержание 250 FleetBroadband

































































































































































































































































































Результаты поиска

Содержание 250 FleetBroadband

Отзывы:

Sailor 250 FleetBroadband, Руководство пользователя, Страница: 248 / 288

Результаты поиска

Содержание 250 FleetBroadband

Отзывы: