Roto-Jet 2200 Скачать руководство пользователя страница 37

 

2200 

34 

Appendix A   

A.1 

2200 Rotor Assembly Drive Conversion. 

(Reference Figure 2-7)

 

A.2 

Preparation.  

Remove rotor assembly per S

ection 3.4

A.3 

Convert from 2200B (belt drive) to 2200A (direct drive).

 

A.3.1  Remove self-locking nut (46) using a bearing locknut wrench adapter.  

Discard 

nut.

 

A.3.2  Remove the spacer (28). 

A.3.3  Install the bearing separator under the thrust bearing (12) in an upside-down 

position.  Make sure the separator is installed so it will pull on the inner race.  
Remove the radial bearing (13B), thrust bearing (12), and spacer set (23) and 
discard. 

A.3.4  Heat the new thrust bearing (12) to 150°-175° F.  Check the temperature with the 

heat stick.  Place the bearing on the shaft with the wide shoulder of the inner race 
against the shoulder of the shaft. 

A.3.5  Place the bearing spacer set (23) around the shaft (5) and against the thrust 

bearing so the retainer shoulders fit in place. 

NOTE:  

The spacer is a matched set, check to be sure that both parts are matched with 

the same set number. 

A.3.6  Heat the angular contact bearing (13A) to 150°-175° F and place it on the shaft 

against the bearing spacer with the wide face of the inner race facing away from 
the bearing spacer (23). 

A.3.7  Install spacer (28) on shaft (5). 

A.3.8  Screw self-locking nut (46) on the shaft (5) and torque to 175 ft. lbs. 

A.3.9  Complete assembly per 

Section 4.2

A.4 

Convert from 2200A (direct drive) to 2200B (belt drive).

 

A.4.1  Repeat section A.3.1 – A.3.9, omit A.1.3.3 and A.1.3.6 and replace with A.4.2 

and A.4.3. 

A.4.2  Install the bearing separator under the thrust bearing (12) in an upside-down 

position.  Make sure the separator is installed so it will pull on the inner race.  
Remove the angular contact bearing (13A), thrust bearing (12), and spacer set (23) 
and discard. 

Содержание 2200










































Отзывы: