Roto-Jet 2200 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 41

Roto-Jet 2200 Скачать руководство пользователя страница 29

2200

26

4.5.2.3

Install and seat seal (75) in seal plate (70). Caution to be taken to avoid
chipping seal face.

4.5.2.4

Replace seal hub (29), if required. Reference Section 4.5.3 for seal hub
replacement.

4.5.2.5

Slide seal plate (70) into endbell (26) with seal outward and drain hole to
bottom of pump. Install 4 socket head cap screws (71) and tighten to 20
ft. lbs.

4.5.2.6

Slide mating ring (78) and o-ring on bug (69). Install retaining ring (91).

4.5.2.7

Clean the pick-up tube and seal cavity in manifold (36).

4.5.2.8

Lubricate manifold seal o-ring (44) and install in groove.

4.5.2.9

Install and seat seal (75) in manifold cavity (36). Caution to be taken to
avoid chipping seal face. Use double seal installation tool (P/N
06058341), if required.

4.5.2.10 Install seal spacer (76), making sure to align the hole in the spacer with

the pin (77) in the manifold.

4.5.3.

Seal Hub Replacement (

Reference Figure 2-9

) – 3-1/2” Seal Only

4.5.3.1

Remove the 9 socket head cap screws (72) that attach hub (29) to rotor

cover.

4.5.3.2

Remove o-ring (51) and clean mating surface on rotor cover (4) (

Figure2-

5

).

4.5.3.3

Lubricate and place new o-ring (51) on seal hub (29). Apply light oil.

4.5.3.4

Install 9 socket head cap screws (72). Tighten to 15 ft. lbs. (20 NM).

4.6.

PICK-UP TUBE AND MANIFOLD INSTALLATION

NOTE:

Before installing the manifold (36) to the endbell (26), it is very important that the

mating machined surfaces of both theses parts be thoroughly cleaned.

4.6.1

Lubricate and install pick-up tube o-ring (49) and pick-up tube nut o-ring
(127) into the pick-up tube (1).

4.6.2

Install two pick-up tube alignment pins (128) into the pick-up tube (1) and
friction ring (145)(P/N 0666227).

«
...
27
28
29
30
31
...
»

Содержание 2200










































Отзывы:

Нет отзывов