Roto-Jet 2200 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 41

Roto-Jet 2200 Скачать руководство пользователя страница 24

2200

21

three evenly spaced, tapped jackscrew holes and using a sling, lift and
remove the endbell (26) from the pedestal/case.

3.4.5

Remove the three socket head cap screws (58) which secure the endplate
(15) to the pedestal/case (17).

3.4.6

Thread the three eyebolts (P/N 0665199) into three tapped holes at the
periphery of the rotor cover (4). Remove the rotor assembly from the
pedestal. Be sure to guide the two oil rings (22) over the shaft and
bearings so they do not get damaged. Place the rotor assembly on the
rotor assembly stand (P/N 060581074 with the rotor cover facing up.
Remove the oil rings (22) from the pedestal/case.

3.5.

ROTOR COVER AND PICK-UP TUBE REMOVAL

3.5.1

Match mark the position of each rotor cover cap screw (7) to their location
and also the rotor to the rotor cover for easier repositioning.

NOTE:

They

MUST

be re-assembled in the same location.

3.5.2

Remove two of the twenty rotor cover socket head cap screws (7) and
install the two rotor cover guide pins (P/N 0665014). Remove the
remaining eighteen socket cap screws (7). Thread three jackscrews
evenly into the three tapped jackscrew holes in the rotor cover until it is
released from the rotor.

3.5.3

Replace the three jackscrews with three ½” eyebolts (P/N 060055411) and
remove the rotor cover (4). Remove the pick-up tube (1) and the rotor o-
ring (6).

3.6. BEARING

REMOVAL

3.6.1

Reinstall rotor cover (4) to the rotor (3) using the match mark from
instruction 3.5.1 above. Do not install rotor o-ring. Thread 20 socket head
cap screws into rotor (4) and tighten (torquing not required at this time.)

3.6.2

Thread three 7/16” eyebolts into three jackscrew holes on edge of rotor
cover (4).

3.6.3

Remove rotor assembly from its stand, and place on a flat surface.
Remove eyebolts from rotor.

3.6.4

Install one 5/8” eye bolt into the end of the shaft.

3.6.5

Thread three cap screws into three jackscrew holes hand tight.

3.6.6

Lift rotor assembly and with rotor end down and shaft up, place rotor
assembly on assembly stand, being sure that the head of each socket

«
...
22
23
24
25
26
...
»

Содержание 2200










































Отзывы:

Нет отзывов