manualshive.com logo in svg

Roto-Jet 2200, Руководство по разборке и сборке, Страница: 27 / 41

Поделиться
Скачать
Roto-Jet 2200 Скачать руководство пользователя страница 27

 

2200 

24 

4.3. ROTOR 

COVER 

INSTALLATION 

4.3.1 

Install a 5/8” eyebolt into the end of the shaft (5).  Remove rotor assembly 
from stand.  Lay rotor assembly on its side.  Thread the three 7/16” 
eyebolts (P/N 0665199) into three holes at the periphery of the rotor (3).  
Place rotor assembly back on the rotor assembly stand with the shaft 
down.  Remove the three eyebolts.  

Note:  This step is not required if 

rotor assembly was not removed.

 

4.3.2 

Lubricate and install rotor o-ring (6) on the lip of the rotor (3).  Place the 
pick-up tube (1) in the rotor.  Lubricate the o-ring bore in the rotor cover 
(4) which engages the rotor o-ring (6). 

4.3.3 

Place the rotor cover (4) using three 7/16” eyebolts (P/N 0665199) on the 
rotor (3) with two alignment pins (P/N 0665014).  Be sure all holes in the 
periphery of the rotor cover line up with the holes in the rotor, as the hole 
pattern is not symmetrical. 

4.3.4 

Install the twenty socket head cap screws (7) into their 

original

 rotor cover 

cap screw holes and tighten evenly to draw the rotor cover down.  It is 
important that the rotor cover does not cock, as the o-ring might be 
damaged.  Torque the cap screws to 68 ft. lbs. 

4.4. ROTOR 

ASSEMBLY INSTALLATION 

4.4.1 

Install the endplate guide pin (P/N 060581220) into the holes in the 

endplate (15).  Lift the rotor assembly by the eyebolts, and carefully slide the 
assembly into the pedestal.  BE SURE THAT: 

A)  The alignment pin in the endplate (15) goes thru the corresponding hole in 

the pedestal (17) so that the vent holes in both pieces will be aligned. 

B)  The shaft does not cock and bind the bearings. 

C)  The eyebolts have a long enough shank so that they will clear the rotor 

housing after the rotor (3), rotor cover (4), and shaft (5) are in place. 

4.4.2 

Remove the alignment tool. 

4.4.3 

Install the endplate to pedestal with three cap screws (58).  Torque to 100 

ft. lbs. 

4.5. SEAL 

INSTALLATION 

4.5.1. 

2-7/8” Type S Single Seal 

4.5.1.1 

Lubricate and install seal mating ring o-ring in the hub of the rotor cover 
(4).  Align the drive pin with the hole in the mating ring and insert the seal 

Содержание 2200










































Отзывы:

Нет отзывов