manualshive.com logo in svg

Roto-Jet 2200, Руководство по разборке и сборке, Страница: 28 / 41

Поделиться
Скачать
Roto-Jet 2200 Скачать руководство пользователя страница 28

 

2200 

25 

mating ring (78) into place.  The seal mating ring should move back and 
forth slightly within the drive-pin hole. 

NOTE:  IF YOU ARE ONLY INSTALLING A PICK-UP TUBE OR SEAL, STEPS 4.5.1.2 

– 4.5.1.4 & 4.5.1.6 ARE NOT REQUIRED. 

4.5.1.2 

For proper bearing and seal location, dimension “B” (as 

shown in Figure 2-

10

) must be controlled.  Use the shimming bar (P/N 060580635) and 

depth micrometer to measure the seal height. 

The seal height measurement is then subtracted from the number 
stamped on the measuring bar.  This will give you dimension “B”.  
Referring to the shim chart (

Table 2-6

) find the box in which the measured 

value “V” falls.  (The shimming chart is based on shims .015” thick, actual 
thickness may vary.) 

4.5.1.3 

Now tilt the pump from its vertical position to a horizontal position.  
Remove the four socket head cap screws (60) and bearing cap (14).  
Install the correct number of shims (38).  Reinstall the bearing cap and 
four cap screws (60) and torque to 35 ft. lbs.  Return the pump to a vertical 
position. 

4.5.1.4 

Again measure dimension “B” to be certain it is now correct. 

4.5.1.5 

Place a dial indicator (P/N 060095053) on the sealing face of the seal 
mating ring (78) and rotate the assembly by hand 360 degrees.  The 
runout of the face must be within .001: (0.025 mm) T.I.R. 

4.5.1.6 

Install alignment tools (P/N 0661975) in rotor case for endbell/rotor 
case/pedestal alignment.  Align endbell so that the Roto-Jet name is at the 
top.  Carefully slide the endbell (26) into place.  Lubricate and install the 
twelve endbell socket head cap screws (63) and torque to 104 ft. lbs. 

4.5.1.7 

Lubricate the seal o-ring (44).  By hand, carefully press the mechanical 
seal (75) into position in the manifold (36).  Care should be taken not to 
scratch or chip the seal face during installation. 

NOTE:  

The seal installation instructions (

Section 4.5

) are for a stationary seal 

arrangement.  For a rotating seal, simply reverse the mating ring and seal.  The 
mating ring (78) in the manifold and the seal (75) in the rotor cover. 

4.5.2. 

3-1/2” Type SD Single/Double Seal 

4.5.2.1 

Apply o-ring lube to new o-ring (44) and install in seal plate (70). 

4.5.2.2 

Apply light oil to seal cavity. 

Содержание 2200










































Отзывы:

Нет отзывов