manualshive.com logo in svg

Roto-Jet 2200, Руководство по разборке и сборке, Страница: 14 / 41

Поделиться
Скачать
Roto-Jet 2200 Скачать руководство пользователя страница 14

 

2200 

11 

ITEM 

NO. 

QTY. 

DESCRIPTION 

PART NUMBER 

50 

1 

O-ring, Manifold (Type SD Seals Only) 

060083913 

51 

1 

O-ring, Seal Hub (Type SD Seals Only) 

060083663 

52 

1 

O-ring, Bearing Cap 

0663084-254 

56 

1 

O-ring, End Plate 

0663084-267 

57 

4 

Capscrew, Socket Head (Cover) 

V3347 

58 

3 

Capscrew, Socket Head (Endplate) 

35705 

60 

4 

Capscrew, Socket Head (Bearing Cap) 

42021 

61 

4 

Capscrew, Socket Head (Manifold Plug) (Flanged 
Only) 

38361 

63 

12 

Capscrew, Socket Head (Endbell) 

38361 

65 

4 

Screw, Drive 

060093116 

67 

1 

Plug, Pipe Oil Fill 

57312 

68 

1 

Gauge, Oil Sight 

0661242 

69 

1 

O-ring, Seal Mating Ring (Type SD Seals Only) 

060083940 

70 

1 

Seal Plate (Type SD Seals Only) 

0665167 

71 

4 

Capscrew, Seal Plate (Type SD Seals Only) 

0665540 

72 

9 

Capscrew, Seal Hub (Type SD Seals Only) 

0665541 

73 

1 

Warning Plate – Direct Drive 
Warning Plate – Belt Drive 

0665538 
0665539 

75 

Var. 

Seal 

See Seal Section 

76 

1 

Seal Spacer (Type SD Seals Only) 

0656253 

77 

1 

Pin, Seal Spacer (Type SD Seals Only) 

060084318 

78 

1 

Seal Mating Ring 

See Seal  Section 

81 

1 

Nut, Lock PUT 

0666615-1 

91 

1 

Retaining Ring (Type SD Seals Only) 

0665293 

92 

Var. 

Pin, Anti-rotation 

See Seal Section 

93 

1 

Seal Flush Ring (Type S Seals Only) (see Note 2) 

0666228 

98 

1 

Isolator, Bearing 

0665352 

100 

1 

Sleeve, Bearing 

0665134 

105 

1 

Warning Plate – Operating Instructions 

0665535 

127 

1 

O-ring, PUT Nut 

58218 

128 

2 

Pin, Aligning PUT 

02412 

145 

1 

Friction Ring 

0666227 

Notes: (1) Standard Units are 17-4 PH.  Contact factory representative for optional 

metallurgy. 

 

(2) Item 93 is supplied in pumps with single type S seals with a seal flush. 

 

(3) Pick-Up Tube kits include the pick-up tube and friction ring (Item 145). 

Содержание 2200










































Отзывы:

Нет отзывов