Roto-Jet 2200 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 41

Roto-Jet 2200 Скачать руководство пользователя страница 25

2200

22

head cap screw is in a ¾” dia. Hole on the outside edge of the stand.
(NOTE: The holes are not located symmetrically.)

3.6.7

Remove self-locking nut (46) using a bearing locknut torque wrench
adapter (P/N 060580571), and

discard locknut.

3.6.8

Remove the spacer.

3.6.9

Install the bearing separator (P/N 060095022) in an upside down position
under the oil slinger (20). Make sure the separator is installed so it will
pull on the inner bearing race. Remove the oil slinger (20), radial bearing
(13A), or thrust bearing (13B) spacer set (23) and the thrust bearing (12)
all at once.

3.6.10 Apply bearing locknut torque wrench adapter (P/N 060580570) and

remove the self-locking nut (47).

Discard locknut.

3.6.11 Again, install the bearing puller, remove the rotor bearing (11) and oil

slinger (19) by hand removing hardened shim (111), wave spring (66), and
endplate (15).

3.6.12 Remove the six socket head cap screws (83) which secure the rotor (3) to

the driveshaft (5). Only if rotor or driveshaft need replacement.

3.6.13 Mark the driveshaft (5) and the rotor (3) so that they may be reassembled

with the same relative positions for balance considerations. Thread two
cap screws evenly into the two tapped jackscrew holes in the driveshaft
flange until the driveshaft is released from the rotor.

3.7. PEDESTAL

SLEEVE

REMOVAL

3.7.1

Inspect bearing sleeve (100) for wear, scratches, or gaul marks. If

present, replace before reassembly.

3.7.2

Removal: Pull or tap bearing sleeve from pedestal bore using puller or

brass rod.

4.

ASSEMBLY OF ROTOR BEARING

Note: Balancing – If any rotating components are replaced, i.e., shaft, rotor, or

rotor cover, the rotor assembly must be balanced in accordance with
section 8. This also applies if wear is present in the rotor or rotor cover.

4.1. BEARING

INSTALLATION

4.1.1

Install plug (133) and o-ring (134) in rotor. Install two guide pins (P/N
0661975) into rotor for shaft alignment. Heat the drive shaft bore in the

«
...
23
24
25
26
27
...
»

Содержание 2200










































Отзывы:

Нет отзывов