Rosemount 848T Скачать руководство пользователя страница 39

Страница: 39 / 60

Reference Manual

00809-0100-4848, Rev AA

July 2009

5-3

Rosemount 848T Wireless

POWER MODULE
REPLACEMENT

Expected power module life is six years at reference conditions.

(1)

When power module replacement is required, open the cover and then

remove the power module. Replace the power module (part number

00753-9220-0001) and close the cover making sure to tighten so that metal

touches metal but do not over tighten.

Handling Considerations

The power module with the wireless unit contains 2 “C” size primary

lithium/thionyl chloride batteries. Each battery contains approximately 2.5

grams of lithium, for a total of 5 grams in each pack. Under normal conditions,

the battery materials are self-contained and are not reactive as long as the

batteries and the power module integrity are maintained. Care should be

taken to prevent thermal, electrical or mechanical damage. Contacts should

be protected to prevent premature discharge.
Use caution when handling the power module. The power module may be

damaged if dropped from heights in excess of 20 feet.
Battery hazards remain when cells are discharged.

Environmental Considerations

As with any battery, local environmental rules and regulations should be

consulted for proper management of spent batteries. If no specific

requirements exist, recycling through a qualified recycler is encouraged.

Consult the materials safety data sheet for battery specific information.

Shipping Considerations

The unit is shipped to you without the power module installed. Please remove

the power module from the unit prior to shipping.
Primary lithium batteries are regulated in transportation by the U.S.

Department of Transportation, and are also covered by International Air

Transport Association (IATA), International Civil Aviation Organization (ICAO),

and European Ground Transportation of Dangerous Goods (ARD). It is the

responsibility of the shipper to ensure compliance with these or any other

local requirements. Please consult current regulations and requirements

before shipping.

SPARE PARTS

Table 5-1. Spare Parts List

(1)

Reference conditions are 70° F (21° C), transmit rate of once per minute, and routing data
for three additional network devices.

Part Description

Part Number

Long-life Power Module, Intrinsically Safe

00753-9220-0001

O-ring for aluminum housing cover

00849-1603-0001

Captive screws for aluminum housing cover

00849-1602-0001

Aluminum housing cover and captive screws (o-ring included)

00849-1601-0001

Electronics module

00849-1600-0001

Kit, Spare Cable gland, 1/2-NPT, 7.5mm - 11.9mm (qty 1)

00648-9010-0001

Kit, Spare Cable gland, 1/2-NPT, thin wire, 3mm - 8mm (qty 1)

00648-9010-0003

Mounting bracket for 2-in. pipe mount - SST bracket and bolts

00848-4350-2001

M20 cable gland adapter (qty 4)

00849-1605-0001

Содержание 848T





























































Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды

Rosemount 848T, Справочное руководство

Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды