Rosemount 848T Скачать руководство пользователя страница 4

Страница: 4 / 60

Reference Manual

00809-0100-4848, Rev AA

July 2009

Rosemount 848T Wireless

Explosions could result in death or serious injury:

Installation of this transmitter in an explosive environment must be in accordance

with the appropriate local, national, and international standards, codes, and

practices. Please review the approvals section of the 848T Wireless reference

manual for any restrictions associated with a safe installation.

• Before connecting a Field Communicator in an explosive atmosphere, ensure the

instruments are installed in accordance with intrinsically safe or non-incendive

field wiring practices. Electrical shock can result in death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may be present on

leads can cause electrical shock. This device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions. This device may not

cause harmful interference. This device must accept any interference received,

including interference that may cause undesired operation. This device must be

installed to ensure a minimum antenna separation distance of 20 cm (7.9 in.)

from all persons.

• The power module may be replaced in a hazardous area. The power module has

surface resistivity greater than one gigaohm and must be properly installed in the

wireless device enclosure. Care must be taken during transportation to and from

the point of installation to prevent electrostatic charge build-up.

Process leaks may cause harm or result in death.

• Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.

• Avoid contact with the leads and terminals. High voltage that may be present on

leads can cause electrical shock.

NOTICE

The Rosemount 848T Wireless and all other wireless devices should be installed only

after the Smart Wireless Gateway has been installed and is functioning properly.

Wireless devices should also be powered up in order of proximity from the Smart

Wireless Gateway, beginning with the closest. This will result in a simpler and faster

network installation.

NOTICE

Shipping considerations for wireless products (Lithium Batteries):

The unit was shipped to you without the power module installed. Please remove the power

module from the unit prior to shipping.
Each power module contains two “C” sized primary lithium batteries. Primary lithium

batteries are regulated in transportation by the U. S. Department of Transportation, and are

also covered by IATA (International Air Transport Association), ICAO (International Civil

Aviation Organization), and ARD (European Ground Transportation of Dangerous Goods).

It is the responsibility of the shipper to ensure compliance with these or any other local

requirements. Please consult current regulations and requirements before shipping.

Содержание 848T





























































Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды

Rosemount 848T, Справочное руководство

Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды