Rosemount 848T Скачать руководство пользователя страница 52

Страница: 52 / 60

Reference Manual

00809-0100-4848, Rev AA

July 2009

Rosemount 848T Wireless

B-2

European Union
Directive Information

The EC declaration of conformity for all applicable European directives for this

product can be found on the Rosemount website at www.rosemount.com. A

hard copy may be obtained by contacting your local sales representative.

ATEX Directive (94/9/EC)

Emerson Process Management complies with the ATEX Directive.

Electro Magnetic Compatibility (EMC) (2004/108/EC)

EN 61326-1: 2006

EN 61326-2-3: 2006

Radio and Telecommunications Terminal Equipment Directive (R&TTE)
(1999/5/EC)

Emerson Process Management complies with the R&TTE Directive.

(1)

Ordinary Location
Certification for FM

As standard, the transmitter has been examined and tested to determine that

the design meets basic electrical, mechanical, and fire protection

requirements by FM, a nationally recognized testing laboratory (NRTL) as

accredited by the Federal Occupational Safety and Health Administration

(OSHA).

Hazardous Locations
Certificates

North American Certifications

Factory Mutual (FM) Approvals

FM Intrinsic Safety and Non-incendive

Intrinsically Safe for Class I, Division 1, Groups A, B, C, and D.

Zone Marking: Class I, Zone 0, AEx ia llC

Temperature Codes T4 (T

amb

= -50 to 70° C)

Non-incendive for Class I, Division 2, Groups A, B, C, and D.

Intrinsically Safe and non-incendive when installed in accordance with

Rosemount drawing 00849-1000.

For use with Rosemount power module P/N 753-9220-XXXX only.

Enclosure Type 4X / IP66

N5 FM Class 1, Division 2, and Dust

Non-incendive for Class 1, Division 2, Groups A, B, C, and D

Dust Ignition-proof for Class II/III, Division 1, Groups E, F, and G

Ambient Temperature Limits -50 to 85° C

Non-incendive when installed in accordance with Rosemount drawing

00849-1000.

For use with Rosemount power module P/N 753-9220-0001 only.

Enclosure Type 4X / IP66

Country

Restriction

Bulgaria

General authorization required for outdoor use and public service

France

Outdoor use limited to 10mW e.i.r.p.

Italy

If used outside of own premises, general authorization is required.

Norway

May be restricted in the geographical area within a radius of 20 km

from the center of Ny-Alesund.

Romania

Use on a secondary basis. Individual license required.

(1)

Only applicable to extended range integral antenna option code WM

Содержание 848T





























































Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды

Rosemount 848T, Справочное руководство

Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды