Rosemount 848T Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

background image

Reference Manual

00809-0100-4848, Rev AA

July 2009

6-3

Rosemount 848T Wireless

Table 6-2. Wireless Network

Troubleshooting

Supply Voltage
Failure

The supply voltage is too low for the
device to function properly.

1. Replace the Power Module.

Supply Voltage
Out of Range

Low supply voltage may affect the
operation of the device.

1. Replace the Power Module.

High Power
Active

The device is operating in a high
power mode ideal for configuration
situations. If the device is
self-powered, using the high power
mode for long periods of time will
significantly reduce the life of the
Power Module.

1. When configuring the device,

activate high power mode.

2. Upon completion of configuration,

disable high power mode.

Device Status

Description

Recommended Actions

Symptom

Recommended Actions

Device not joining the

network

Verify Network ID and Join Key
Wait longer (30 min.)
Enable High Speed Operation on Smart Wireless Gateway
Check the Power Module
Verify the device is within range of at least one other device
Verify network is in active network advertise
Power Cycle device to try again
Verify device is configured to join. Send the “Force Join”
command to the device
See the Troubleshooting section of the Smart Wireless Gateway
manual for more information.

Short Battery Life

Check that “Power Always On” mode is off
Verify the device is not installed in extreme temperatures
Verify that the device is not a network pinch point
Check for excessive network rejoins from poor connectivity

Limited Bandwidth Error

Reduce the Update Rate on the transmitter
Increase communication paths by adding more wireless points

«
...
41
42
43
44
45
...
»

Содержание 848T





























































Отзывы:

Нет отзывов

Похожие инструкции для 848T

Бренд: Cabletron Systems Страницы: 26

Бренд: Campbell Страницы: 50

Бренд: Ranger Communications Страницы: 11

Бренд: WDS Страницы: 32

Бренд: Icom Страницы: 73

Бренд: TV One Страницы: 10

JLT-6000 series

Бренд: Jogler Страницы: 16

Бренд: Kanomax Страницы: 27

Бренд: M-system Страницы: 5

CentreCOM AT-280

Бренд: Allied Telesis Страницы: 4

ATLANTIS250 BK - ATLANTIS 250 VHF Radio

Бренд: Uniden Страницы: 36

2004-6191-1100-001

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Jobsite Страницы: 2

Бренд: J&E Hall Страницы: 18

Бренд: Baofeng Страницы: 20

Бренд: Mercoid Страницы: 20

Бренд: Audioplex Страницы: 2

Бренд: VESALA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды