Rosemount 848T Скачать руководство пользователя страница 15

Страница: 15 / 60

Reference Manual

00809-0100-4848, Rev AA

July 2009

2-3

Rosemount 848T Wireless

DEFAULT SETTINGS

The 848T default configuration is shown below:

Use the C1 option code to have the factory configure each sensor individually.

This option also enables factory configuration of process alerts, update rate,

and channel tag. This option code is not required to configure the

self-organizing network parameters, or to set all of the sensors identically.

DEVICE NETWORK
CONFIGURATION

Join Device to Network

The transmitter must be configured in order to communicate with the Smart

Wireless Gateway, and ultimately with the host system. This step is the

wireless equivalent of connecting wires from the transmitter to the host

system.

1. From the

Home

screen, select 2:

Configure.

2. Select 1:

Guided Setup

3. Select 1:

Join Device to Network

Using a Field Communicator or AMS, enter the Network ID and Join Key so

they match the Network ID and Join Key of the Smart Wireless Gateway, and

other devices in the network. If the Network ID and Join Key do not match the

Gateway, the transmitter will not communicate with the network. The Network

ID and Join Key can be obtained from the Smart Wireless Gateway on the

Setup>Network>Settings

page on the web server.

Sensor 1

Type J Thermocouple

Sensor 2

Type J Thermocouple

Sensor 3

Type J Thermocouple

Sensor 4

Type J Thermocouple

Engineering Units

°C

Number of Lead Wires

Sensor Alerts

Disabled

Network ID

Factory Generated Network Parameters

Join Key

Factory Generated Network Parameters

Update Rate

1 Minute

Fast Key

2, 1, 1

Содержание 848T





























































Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды

Rosemount 848T, Справочное руководство

Результаты поиска

Содержание 848T

Отзывы:

Похожие инструкции для 848T

Бренды по названию

Популярные бренды