Rosemount 848T Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 60

background image

Reference Manual

00809-0100-4848, Rev AA

July 2009

Rosemount 848T Wireless

www.rosemount.com

Section 2

Configuration

Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Bench Top Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-2
Default Settings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-3
Device Network Configuration   . . . . . . . . . . . . . . . . . . . . . page 2-3
Sensor Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-4
Advanced Configuration (Optional)   . . . . . . . . . . . . . . . . . page 2-5
HART® Menu Tree   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2-7

SAFETY MESSAGES

Instructions and procedures in this section may require special precautions to

ensure the safety of the personnel performing the operations. Information that

potentially raises safety issues is indicated by a warning symbol ( ). Please

refer to the following safety messages before performing an operation

preceded by this symbol.

Warnings

Failure to follow these installation guidelines could result in death or
serious injury.

• Make sure only qualified personnel perform the installation.

Explosions could result in death or serious injury.

• Before connecting a 375 Field Communicator in an explosive atmosphere, make

sure the instruments are installed in accordance with intrinsically safe or

non-incendive field wiring practices.

• Verify that the operating atmosphere of the transmitter is consistent with the

appropriate hazardous locations certifications.

Process leaks could result in death or serious injury.

• Do not remove the thermowell while in operation.
• Install and tighten thermowells and sensors before applying pressure

Electrical shock could cause death or serious injury.

• Use extreme caution when making contact with the leads and terminals.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions: This device may not cause harmful interference, this device must accept any

interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of 20 cm

from all persons.

If the sensor is installed in a high-voltage environment and a fault condition or installation

error occurs, the sensor leads and transmitter terminals could carry lethal voltages. Use

extreme caution when making contact with the leads and terminals.

«
...
11
12
13
14
15
...
»

Содержание 848T





























































Отзывы:

Нет отзывов

Похожие инструкции для 848T

Бренд: Hallicrafters Страницы: 43

Бренд: halstrup-walcher Страницы: 23

Бренд: Mammut Страницы: 40

Бренд: Omega Страницы: 2

CCX Lipo 2,4 GHz 3 CH

Бренд: Jamara Страницы: 12

STINGER2 433TSD22V2

Бренд: Transmitter Solutions Страницы: 2

Бренд: M-system Страницы: 3

Бренд: Realistic Страницы: 14

Бренд: SICK STEGMANN Страницы: 8

Бренд: Yaesu Страницы: 50

Бренд: OEM Страницы: 104

Бренд: dB Страницы: 101

Бренд: Pro2 Страницы: 4

Бренд: Icom Страницы: 40

Бренд: Icom Страницы: 60

Бренд: Icom Страницы: 96

Бренд: Icom Страницы: 17

Бренд: Icom Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды