Rosemount 2240S Скачать руководство пользователя страница 17

Страница: 17 / 100

Reference Manual

300550EN, Rev AA
December 2010

2-7

Rosemount 2240S

Section 2. Overview

2.4 GETTING STARTED

To start up a Raptor system do the following:

1. Install the TankMaster software on the control room PC.
2. Prepare the the start-up by recording the information that will be needed

for configuration of the various devices as described in the Rosemount
Raptor System Configuration manual.

3. Connect the Rosemount 2160 Field Communication Unit to the

TankMaster PC. The 2160 may be connected via a Rosemount 2180
Field Bus Modem, or directly via RS232 or RS485 interface.

4. Connect the Rosemount 2410 Tank Hub to the 2160 Field

Communication Unit.

5. Connect the field devices, such as Rosemount 5900S Radar Level

Gauge and Rosemount 2240S Multi-input Temperature Transmitter, to
the 2410 Tank Hub via the Tankbus.

6. Configure the 2160 Field Communication Unit (if included in the system)

by using the TankMaster WinSetup configuration software.

7. Configure the 2410 Tank Hub by using the TankMaster WinSetup

configuration software.

8. Configure the field devices, such as the 5900S and the 2240S, by using

the TankMaster WinSetup configuration software.

See the Rosemount Raptor System Configuration manual (Document No.
300510EN) for more information on how to configure the various Raptor
devices.

Содержание 2240S





































































































Результаты поиска

Содержание 2240S

Отзывы:

Похожие инструкции для 2240S

Бренды по названию

Популярные бренды

Rosemount 2240S, Справочное руководство

Результаты поиска

Содержание 2240S

Отзывы:

Похожие инструкции для 2240S

Бренды по названию

Популярные бренды